Producto terminadoview
The Permatex 81160 Hi-Temp Red Form-A-Gasket Silicone Sealant is a high-performance silicone gasket maker designed for high-temperature applications and heavy-duty use. It forms a durable, flexible, and waterproof seal, resisting temperatures from -65°F to 650°F (-54°C to 343°C) intermittently. This product is ideal for creating formed-in-place gaskets or sealing pre-cut gaskets in various automotive and industrial applications.
Image: Permatex 81160 Hi-Temp Red Form-A-Gasket Silicone Sealant tube. This image shows the product packaging, a red tube of sealant with the Permatex logo and product name.
Información de seguridad
Read all safety precautions before use. Do not handle until all safety instructions are understood.
Prevención:
- Contains: Calcium carbonate, iron oxide.
- Obtenga instrucciones especiales antes de usar.
- Use equipo de protección personal según sea necesario.
Respuesta:
- SI EN LOS OJOS: Enjuague cuidadosamente con agua durante varios minutos. Quítese los lentes de contacto, si están presentes y son fáciles de hacer. Continúe enjuagando. Si la irritación de los ojos persiste: busque atención o asesoramiento médico.
- SI EN LA PIEL: Wash with plenty of soap and water. If skin irritation or rash occurs: Get medical advice/attention. Wash contaminated clothing before reuse.
Almacenamiento:
- Proteger de la luz solar.
- Almacenar en un lugar bien ventilado.
- Tienda cerrada.
Desecho:
- Eliminar el contenido/el recipiente en una planta de eliminación de residuos aprobada.
- Mantener fuera del alcance de los niños.
Image: Back of Permatex 81160 packaging. This image displays the detailed safety warnings, directions for use, and precautionary statements in English and Spanish.
Instrucciones de aplicación
Preparación:
- For best results, ensure surfaces are clean and dry.
Solicitud:
- Cut the nozzle to the desired bead size (typically 1/16" to 1/4" or 2 to 6mm).
- Apply a continuous bead of silicone to one surface, ensuring it surrounds all bolt holes.
- Ensamble las piezas inmediatamente mientras la silicona aún esté húmeda.
- Finger tighten until material begins to squeeze out around the flange.
Curado y acabado:
- Allow the sealant to dry for one hour, then tighten to torque specifications.
- Allow 24 hours for the sealant to fully cure before filling with fluids or returning to service.
- Replace the cap after use to prevent drying.
NOTE: Not recommended for use on head gaskets or parts in contact with gasoline.
Image: Formed-in-Place Gasket. A hand applies Permatex sealant to an engine component, demonstrating the application process for creating a gasket.
Aplicaciones sugeridas
Permatex 81160 Hi-Temp Red Form-A-Gasket Silicone Sealant is suitable for a variety of high-temperature and heavy-duty applications, including:
- tapas de valvulas
- Cárteres de aceite
- Timing covers
- Bombas de agua
- Thermostat housings
- Bandejas de transmisión
Image: Suggested Applications. This banner image shows various engine components like valve covers and water pumps, highlighting the sealant's intended uses.
Presupuesto
| Característica | Especificación |
|---|---|
| Material | Silicona |
| Color | Rojo |
| Formulario de artículo | Líquido |
| Recuento de unidades | 3.0 onzas líquidas |
| Resistencia a la temperatura | -65°F to 650°F (-54°C to 343°C) intermittent |
| Nivel de resistencia al agua | Impermeable |
| Número de modelo del artículo | 81160 |
| Número de pieza del fabricante | 81160 |
| País natal | Porcelana |
Solución de problemas
Si encuentra problemas durante o después de la aplicación, considere lo siguiente:
- Fuga: Ensure surfaces were thoroughly cleaned and dried before application. Verify that a continuous bead was applied and that parts were assembled while the silicone was still wet. Allow the full 24-hour cure time before exposing to fluids or service.
- Mala adherencia: Surface preparation is critical. Ensure all oil, grease, and old gasket material are removed. The sealant may not adhere properly to contaminated surfaces.
- Problemas de curación: Ensure the product was stored correctly and is within its shelf life. Proper ventilation during curing is also important.
For persistent issues, refer to the Permatex websitio o póngase en contacto con el servicio de atención al cliente.
Garantía y soporte
For information regarding product warranty, technical support, or frequently asked questions, please visit the official Permatex webSitio web o contacte con el departamento de atención al cliente. Conserve el recibo de compra para cualquier reclamación de garantía.