Pyramis Festivo ND Kitchen Faucet Instruction Manual

1. Producto terminadoview

The Pyramis Festivo ND kitchen faucet is a single-lever mixer designed for use with low-pressure water heater systems. It features a high-quality chrome-plated brass construction, a swiveling spout, and an extendable pull-out spray for versatile use. The faucet is equipped with a durable ceramic cartridge and a removable, washable aerator for easy maintenance. Its design provides convenience for rinsing sinks and dishes.

2. Información de seguridad

• Always turn off the main water supply before attempting any installation, maintenance, or repair work on the faucet.
• Asegúrese de que todas las conexiones estén seguras para evitar fugas.
• Do not use abrasive cleaners, scouring pads, or chemicals that may damage the chrome finish.
• Si no está seguro acerca de alguno de los pasos de instalación, consulte a un plomero calificado.
• This faucet is specifically designed for low-pressure water heater systems. Do not connect to high-pressure systems.

3. Contenido del paquete

Verifique que todos los componentes estén presentes antes de comenzar la instalación:

• Pyramis Festivo ND Kitchen Faucet (chrome-plated brass body)
• Plastic Pull-Out Spray Head
• Mangueras de conexión
• Mounting Material (gaskets, nuts, washers)
• Ceramic Cartridge (pre-installed)
• Removable Aerator (pre-installed)

4. Especificaciones

5. Configuración e instalación

Before installation, ensure you have the necessary tools (e.g., adjustable wrench, screwdriver, sealant tape). This faucet requires a minimum faucet hole diameter of 35 mm. It is not designed for direct connection to angle valves.

5.1 Diagrama de instalación

5.2 Instalación paso a paso

1. Prepare la superficie de montaje: Ensure the sink or countertop has a pre-drilled hole with a diameter of at least 35 mm. Clean the area around the hole.
2. Instalar el grifo: Insert the faucet body through the mounting hole. Ensure the base gasket is correctly positioned between the faucet and the mounting surface.
3. Asegure el grifo: From underneath the sink, slide the rubber washer, metal washer, and mounting nut onto the threaded shank of the faucet. Tighten the mounting nut securely with an appropriate wrench.
4. Conectar mangueras de agua: Connect the hot and cold water supply hoses to the corresponding inlets on the faucet body. Use sealant tape on the threads if necessary to ensure a watertight seal. Connect the other ends of the hoses to your low-pressure water supply lines.
5. Install Pull-Out Spray Hose: Connect the pull-out spray hose to the designated outlet on the faucet body. Ensure the hose moves freely and does not kink.
6. Attach Counterweight (if included): If a counterweight is provided for the pull-out spray hose, attach it to the hose at the recommended position to ensure smooth retraction.
7. Prueba de fugas: Slowly turn on the main water supply. Check all connections for any signs of leaks. If leaks occur, tighten the connections carefully.
8. Check Faucet Functionality: Operate the lever to check hot and cold water flow. Extend and retract the pull-out spray to ensure it functions correctly.

6. Instrucciones de funcionamiento

• Control de flujo de agua y temperatura: The single lever controls both water flow and temperature. Lift the lever to increase water flow. Move the lever left for hot water and right for cold water.
• Caño giratorio: The faucet spout can be swiveled from side to side, allowing you to direct water flow across different areas of your sink.
• Spray extraíble: To use the pull-out spray, simply grasp the spray head and pull it out from the spout. The hose extends, providing flexibility for rinsing. After use, guide the spray head back into the spout until it clicks into place.

7. Mantenimiento

7.1 Limpieza del grifo

• Limpie la superficie cromada regularmente con un paño suave y jabón suave o un limpiador no abrasivo diseñado específicamente para acabados cromados.
• Enjuague bien con agua limpia y seque con un paño suave para evitar manchas de agua.
• Avoid using abrasive cleaners, acids, alcohol, or harsh chemicals, as these can damage the chrome finish.

7.2 Cleaning the Aerator

The aerator can be removed and cleaned to maintain optimal water flow and prevent mineral buildup.

1. Unscrew the aerator from the tip of the spout (a coin or aerator key may be needed).
2. Separate the mesh screens and rinse them under running water to remove any debris or mineral deposits.
3. For stubborn deposits, soak the aerator components in a solution of equal parts white vinegar and water for a few hours.
4. Rinse thoroughly and reassemble the aerator, then screw it back onto the spout.

8. Solución de problemas

9. Garantía y soporte

For information regarding warranty coverage or technical support, please refer to the warranty card included with your product or contact Pyramis customer service directly. Keep your purchase receipt as proof of purchase.