Introducción
This manual provides instructions for the proper installation, operation, and maintenance of the Hager 4500 Series Grade 1 Heavy Duty Fire Rated Rim Type Exit Device. This device is engineered for superior performance and meets stringent safety and performance standards, including BHMA Grade 1 certification and UL listing for fire-rated applications.
Información de seguridad
- Always follow local building codes and safety regulations during installation.
- Ensure all components are securely fastened before operation to prevent malfunction.
- This device is intended for use as panic hardware and in fire-rated applications. Do not modify the device or its components.
- Utilice equipo de protección personal (EPP) adecuado, como gafas y guantes de seguridad, durante la instalación.
- Mantenga a los niños y al personal no autorizado alejados del área de instalación.
Contenido del paquete
The Hager 4500 Series Rim Type Exit Device package typically includes:
- Hager 4500 Series Rim Type Exit Device (main assembly)
- Installation Hardware (screws, fasteners)
- Installation Template (for precise marking)
- Manual de instrucciones (este documento)
Image: Main components of the Hager 4500 Series Rim Type Exit Device, showing the push bar, housing, and mounting hardware. This image illustrates the primary parts included in the package.
Configuración e instalación
Proper installation is crucial for the safe and effective operation of the exit device. Refer to the included installation template for precise measurements and drilling instructions specific to your door type.
Herramientas necesarias
- Taladro y brocas adecuadas
- Destornilladores (Phillips y Flathead)
- Cinta métrica
- Lápiz o marcador
- Gafas de seguridad
Pasos de instalación
Prepara la puerta: Mark the center line of the door and the desired height for the exit device. Use the provided template to accurately mark all drilling locations for the device body and strike plate on both the door and frame.
Mount the Device Body: Drill pilot holes as marked on the door. Secure the main body of the exit device to the door using the provided screws. Ensure the device is level and flush against the door surface for optimal performance.
Instalar la placa de impacto: Position the strike plate on the door frame, aligning it precisely with the latch bolt of the exit device. Mark and drill pilot holes, then secure the strike plate with the appropriate screws.
Connect Exterior Trim (if applicable): If an exterior trim (e.g., lever, pull, or key cylinder) is being installed, follow its specific instructions to connect it to the internal mechanism of the exit device. Ensure proper engagement and function.
Operación de prueba: Close the door and depress the push bar firmly. Verify that the latch bolt retracts smoothly and fully, allowing the door to open freely. Check for any binding, resistance, or improper latching.
Ajustes: Make any necessary fine adjustments to the strike plate or device body to ensure perfect alignment and consistently smooth operation. All screws should be tightened securely, but not overtightened.
Instrucciones de funcionamiento
The Hager 4500 Series Rim Type Exit Device is designed for intuitive and reliable emergency egress.
To Exit (Egress)
Depress Push Bar: Apply firm, even pressure to the push bar located across the width of the door.
Puerta abierta: As the push bar is depressed, the internal mechanism will retract the latch bolt, allowing the door to swing open outwards.
To Enter (Ingress, with exterior trim)
Use Exterior Trim: If an exterior trim with a lever, knob, or key cylinder is installed, operate it according to its specific instructions (e.g., turn lever, insert key) to retract the latch bolt.
Puerta abierta: Push or pull the door open once the latch bolt is retracted.
Mantenimiento
Regular maintenance ensures the longevity, reliability, and continued compliance of your Hager 4500 Series Exit Device.
Limpieza: Clean the device surfaces with a soft, damp cloth. Avoid using abrasive cleaners, harsh chemicals, or solvents that may damage the finish or internal components.
Lubricación: Periodically (e.g., annually or semi-annually, depending on usage) apply a small amount of silicone-based lubricant to moving parts, such as the latch bolt and internal mechanisms. Do not over-lubricate, as this can attract dirt.
Inspección: Annually inspect all mounting screws for tightness. Check the push bar for any signs of damage, bending, or excessive wear. Ensure the latch bolt retracts fully and smoothly without obstruction. Verify that the device operates freely and returns to its original position.
Cumplimiento de las normas de puertas cortafuegos: For devices installed on fire-rated doors, it is critical to ensure that no modifications are made to the device or door that would compromise its fire rating. Any repairs or replacements must use approved components.
Solución de problemas
This section addresses common issues you might encounter with your exit device.
| Problema | Posible causa | Solución |
|---|---|---|
| Device binds or is difficult to operate | Misalignment of device or strike plate, worn parts, lack of lubrication, debris accumulation | Check and adjust the alignment of the device body and strike plate. Lubricate moving parts with silicone spray. Inspect for and remove any obstructions or debris. |
| Latch bolt does not retract fully | Obstruction in strike plate, bent latch bolt, internal mechanism issue, incorrect installation | Clear any obstructions from the strike plate. Inspect the latch bolt for damage; replace if bent. If the issue persists, it may indicate an internal mechanism problem requiring professional service. |
| El dispositivo se siente flojo o inestable | Loose mounting screws, damaged door or frame | Tighten all mounting screws securely. Do not overtighten. If the door or frame is damaged, repair it before re-mounting the device. |
| Exterior trim (if installed) does not operate | Improper connection to exit device, faulty trim mechanism | Verify the connection between the exterior trim and the exit device. Consult the trim's specific installation instructions. If the trim itself is faulty, it may need replacement. |
Presupuesto
- Modelo: 158103
- Serie: Serie 4500
- Tipo: Rim Type Exit Device
- Longitud: 36 pulgadas
- Finalizar: Bronce frotado con aceite
- Material: AL/Stainless Steel/Zinc
- Calificación: BHMA Certified ANSI A156.3 Grade 1
- Resistencia al fuego: UL/cUL Listed up to 3 Hours for "A" labeled doors
- Panic Listing: UL305 Listed for panic hardware
- Windstorm Resistance: ANSI A250.13 Severe Windstorm Resistant Component
- Accesibilidad: Complies with ANSI A117.7 for accessible buildings
- Dimensiones del producto: 36 x 10 x 5 pulgadas
- Peso del artículo: 13 libras
- Componentes incluidos: Hardware de instalación
Información de garantía
The Hager 4500 Series exit device is backed by a garantía de por vida, providing assurance of quality and durability from the manufacturer to the building owner. For detailed warranty terms, conditions, and claim procedures, please refer to the official Hager Companies warranty documentation or contact Hager customer support directly.
Atención al cliente
For technical assistance, replacement parts, or warranty claims, please contact Hager Companies directly.
Fabricante: Empresas Hager
Websitio: www.hagerco.com
Teléfono: Please refer to the Hager Companies official website for the most current contact numbers and support options.
