PAC RP4.2-HY12 RadioPRO Radio Replacement Interface User Manual

Introducción

This manual provides detailed instructions for the installation and operation of the PAC RP4.2-HY12 RadioPRO Radio Replacement Interface. This all-in-one interface is designed to facilitate the replacement of a factory radio in select Hyundai vehicles while retaining essential vehicle features, including pre-programmed steering wheel controls, amplifier retention, and navigation-based output signals.

Información de seguridad

• Desconecte la batería del vehículo antes de la instalación para evitar cortocircuitos eléctricos.
• Ensure all connections are secure and properly insulated to avoid damage to the interface or vehicle electronics.
• Consulte con un técnico automotriz profesional si no está seguro acerca de alguno de los pasos de instalación.
• This device is intended for use in specific Hyundai vehicles as indicated by the manufacturer. Verify compatibility before installation.

Contenido del paquete

Verify that all items are present before beginning installation.

• PAC RP4.2-HY12 RadioPRO Interface Module
• Arneses de cableado (específicos del vehículo)
• Guía de instalación (este documento)

Image: The PAC RP4.2-HY12 RadioPRO interface module, typically a compact black box with various wiring connectors.

Configuración e instalación

The PAC RP4.2-HY12 is designed for select Hyundai Veloster vehicles. Refer to the vehicle-specific wiring diagram for your exact model.

Notas previas a la instalación

• This interface does not retain Blue Link functionality. For Blue Link retention, the RP5.2-HY12 model is required.
• In vehicles equipped with auto climate controls, the fan mode, fan speed, auto status, and temperature display may not be visually confirmed on the new radio. The functions will still operate.
• The interface provides data-controlled accessory and navigation outputs.
• A 10A accessory output is provided.

Pasos generales de instalación

1. Desconecte la batería: Before starting, disconnect the negative terminal of the vehicle's battery.
2. Quitar la radio de fábrica: Carefully remove the factory radio from the dashboard.
3. Conectar los arneses de cableado:
   • Connect the vehicle-specific harness from the RP4.2-HY12 module to the factory wiring harness in the vehicle.
   • Connect the aftermarket radio harness to the RP4.2-HY12 module's output harness. Ensure all wires are matched correctly (e.g., power, ground, speakers, accessory, illumination).
4. Connect Steering Wheel Control (SWC) Wire: Connect the SWC output wire from the RP4.2-HY12 to the appropriate SWC input wire on your aftermarket radio. Refer to your aftermarket radio's manual for SWC input location.
5. Connect Navigation Outputs (if applicable): Connect the navigation outputs (e.g., VSS, Reverse, Parking Brake) from the RP4.2-HY12 to the corresponding inputs on your aftermarket navigation radio.
6. Montar el módulo: Securely mount the RP4.2-HY12 module in a location that does not interfere with vehicle operation or reassembly of the dashboard.
7. Vuelva a conectar la batería: Vuelva a conectar el terminal negativo de la batería del vehículo.
8. Sistema de prueba: Turn on the vehicle and test all functions of the aftermarket radio, including audio, steering wheel controls, and navigation features.

Operación

The PAC RP4.2-HY12 interface is designed to seamlessly integrate your aftermarket radio with your vehicle's existing systems, primarily focusing on steering wheel control retention.

Control del volante (SWC)

The interface comes pre-programmed to retain the factory steering wheel controls. Once installed, the buttons on your steering wheel should operate the corresponding functions on your aftermarket radio (e.g., volume up/down, track up/down, mode).

• Control de volumen: Use the volume buttons on your steering wheel to adjust the audio level.
• Seguimiento/búsqueda: Use the track or seek buttons to change radio stations or music tracks.
• Modo/Fuente: Use the mode or source button to switch between audio sources (e.g., AM/FM, CD, Bluetooth, USB).

Note: Specific button functions may vary slightly depending on the aftermarket radio model and vehicle configuration. Refer to your aftermarket radio's manual for custom programming options if available.

Solución de problemas

No Power to Aftermarket Radio

• Check the vehicle's fuse box for blown fuses.
• Verify all power and ground connections from the RP4.2-HY12 harness to the aftermarket radio and vehicle.
• Asegúrese de que la batería del vehículo esté completamente cargada y conectada correctamente.

Los controles del volante no funcionan

• Confirm the SWC wire from the RP4.2-HY12 is correctly connected to the aftermarket radio's SWC input.
• Check the aftermarket radio's settings to ensure SWC is enabled and configured for a PAC interface, if applicable.
• Some aftermarket radios require a specific programming sequence for SWC; consult your radio's manual.
• Usuario Review Note: One user reported losing steering controls when using the audio jack provided with a similar kit. If experiencing issues, try disconnecting any auxiliary audio jacks if present and re-test SWC.

Sin salida de audio

• Verify all speaker wire connections are secure and correctly matched.
• Ensure the aftermarket radio's amplifier turn-on wire is connected to the RP4.2-HY12's amplifier turn-on output (if applicable for factory amplifier retention).
• Check the aftermarket radio's volume and mute settings.

Presupuesto

Garantía y soporte

For warranty information and technical support, please contact PAC customer service directly. Keep your purchase receipt as proof of purchase.

Recursos en línea: Visit the official PAC website for the latest product information, firmware updates, and additional support resources.

Información del contacto: Refer to the PAC webSitio o embalaje del producto para obtener información de contacto actualizada.