Eldom 72324PMP 7-Liter Under-Sink Pressure-Resistant Water Heater User Manual

1. Instrucciones de seguridad

Please read these safety instructions carefully before installing, operating, or performing maintenance on the appliance. Failure to follow these instructions may result in electric shock, fire, property damage, or personal injury.

• La instalación y las conexiones eléctricas deben ser realizadas por personal calificado de acuerdo con las regulaciones locales.
• Asegúrese de que el aparato esté correctamente conectado a tierra.
• No opere el calentador de agua si el cable de alimentación o el enchufe están dañados.
• Always ensure the water heater is filled with water before switching on the power.
• The pressure relief valve must be installed and maintained correctly to prevent excessive pressure build-up. Do not block or tamper con la válvula.
• Mantenga los materiales inflamables alejados del aparato.
• Este aparato está diseñado para uso en interiores únicamente.

2. Producto terminadoview

The Eldom 72324PMP is a compact 7-liter under-sink electric water heater designed for pressure-resistant operation. It features a durable steel tank with high-performance enamel and additional anode protection against corrosion, ensuring a long service life. An integrated anti-return valve prevents backflow and protects against overpressure. The continuous temperature regulator allows precise control over water temperature.

Figure 1: Eldom 72324PMP 7-Liter Under-Sink Water Heater. This image shows the compact design suitable for under-sink installation.

Características principales:

• Capacidad: 7 litros
• Tipo de instalación: Under-sink, pressure-resistant
• Material del tanque: Steel with high-performance enamel coating
• Protección contra la corrosión: Anode protection system
• Seguridad: Integrated anti-return valve and safety valve
• Control de temperatura: Continuous temperature regulator
• Fuerza: 1500 W
• Eficiencia Energética: Clase B

3. Especificaciones técnicas

Figure 2: Energy Label for Eldom 72324PMP, indicating Class B efficiency and 95 kWh/annum consumption.

Para obtener información más detallada sobre el producto, consulte la base de datos EPREL: https://eprel.ec.europa.eu/qr/85466

4. Configuración

4.1 Colocación

• The water heater is designed for under-sink installation. Ensure there is sufficient space for the unit and its connections.
• Mount the unit securely to a solid surface, such as a wall, using appropriate fasteners. The unit is designed for wall mounting.
• Asegúrese de que el lugar esté protegido de temperaturas bajo cero.

4.2 Conexión de agua

Connect the water heater to the cold and hot water supply using 1/2 inch connections. It is crucial to install the supplied safety valve on the cold water inlet. This valve prevents excessive pressure build-up inside the tank.

1. Install the safety valve on the cold water inlet pipe. Ensure the arrow on the valve points towards the water heater.
2. Connect the cold water supply to the inlet of the safety valve.
3. Connect the hot water outlet of the water heater to the hot water tap.
4. Open the hot water tap to allow air to escape while the tank fills with water.
5. Once water flows steadily from the hot water tap, close the tap. Check all connections for leaks.

4.3 Conexión eléctrica

The appliance comes with a power cable and plug. Ensure the electrical outlet is properly grounded and matches the voltage and frequency requirements (230V/50Hz).

• Before plugging in the appliance, ensure the water tank is completely filled.
• Conecte el cable de alimentación a una toma eléctrica adecuada con conexión a tierra.
• No utilice cables de extensión ni adaptadores.

5. Operando

5.1 Arranque inicial

After installation and filling the tank with water, the unit is ready for operation.

1. Ensure the water heater is properly connected to both water and electricity.
2. Turn on the power supply to the unit. The indicator light (if present) should illuminate.
3. The water heater will begin heating the water to the set temperature. The initial heating cycle for 7 liters from 12°C to 65°C takes approximately 13 minutes.

5.2 Ajuste de temperatura

The water heater is equipped with a continuous temperature regulator, usually a dial or knob on the front or bottom of the unit.

• Rotate the temperature regulator to your desired setting. Higher settings will result in hotter water.
• El termostato mantendrá automáticamente la temperatura establecida.

6. Mantenimiento

Regular maintenance ensures optimal performance and extends the lifespan of your water heater. Always disconnect the power supply before performing any maintenance.

6.1 Limpieza Regular

• Limpie el exterior de la unidad con un paño suave yamp Paño. No utilice limpiadores abrasivos ni disolventes.
• Periodically check the safety valve for proper operation. Refer to the safety valve manufacturer's instructions for testing.

6.2 Descalcificar

Depending on water hardness, scale deposits may accumulate inside the tank and on the heating element, reducing efficiency. Descaling should be performed periodically by a qualified technician.

• Disconnect the power supply and drain the water heater.
• Access the heating element and tank interior to remove scale deposits.
• Replace the anode rod if it is significantly depleted, as it is crucial for corrosion protection.

7. Solución de problemas

Antes de contactar con el servicio de atención al cliente, consulte los siguientes problemas y soluciones comunes:

8. Garantía y soporte

This Eldom water heater is manufactured to high-quality standards. For warranty information, please refer to the documentation provided with your purchase or contact your retailer.

Información de contacto del fabricante:

• Fabricante: Eldominvest
• Websitio: https://eldominvest.com/
• Correo electrónico: tech@eldominvest.com
• Teléfono: +359 52 571 914
• DIRECCIÓN: Boulevard "Vladislav Varnenchik" 275A, 9009 Varna, Bulgaria