Command 17003-MPES

Command 5 lb Large Utility Hooks (Model 17003-MPES) Instruction Manual

Damage-Free Hanging Solution

Introducción

The Command 5 lb Large Utility Hooks provide a damage-free solution for organizing and decorating your home, office, or dorm room. These hooks utilize advanced adhesive technology to hold strongly on various smooth surfaces and remove cleanly without leaving holes, marks, or sticky residue. Each large utility hook is designed to hold up to 5 pounds, offering versatile hanging options for a range of items.

Información de seguridad

  • No colgar sobre las camas.
  • No lo use en papel tapiz.
  • Do not use for hanging valuable items.
  • Ensure indoor temperature is between 50°F (10°C) and 105°F (40°C) for optimal adhesion.
  • Wait seven days after painting before using Command Hooks to allow paint to cure.

Contenido del paquete

Each package of Command 5 lb Large Utility Hooks includes:

  • 14 x Large Utility Hooks
  • 16 x Large Adhesive Strips

Configuración e instalación

Follow these steps for proper installation to ensure maximum holding power and damage-free removal.

1. Preparación de la superficie

Clean the desired surface with rubbing alcohol to remove any grime and dust. This allows the adhesive strips to bond effectively. Do not use household cleaners or water, as they can leave slippery residues that prevent proper adhesion.

2. Attaching Strips to Hooks

Separate the adhesive strips. Each strip has two sides. One side is marked for the wall, and the other for the hook.

Image showing a hand attaching a Command adhesive strip to the back of a white utility hook.

Image: A hand demonstrates attaching the adhesive strip to the flat back of a Command Large Utility Hook. The strip is white with red 'Command' branding.

Press the adhesive strip firmly onto the back of the hook. Ensure the entire strip is pressed down for 30 seconds to create a strong bond.

3. Applying Hooks to the Wall

Remove the remaining liner from the adhesive strip, exposing the side that will attach to the wall.

Image showing a hand pressing a white Command utility hook with an attached adhesive strip onto a clean wall surface.

Image: A hand presses a white Command Large Utility Hook firmly against a wall, demonstrating the application process.

Press the hook firmly against the prepared surface for 30 seconds. Apply pressure evenly across the entire hook to ensure full contact with the adhesive.

4. Curing Time

After applying the hook, wait 1 hour before hanging any items. This allows the adhesive to reach its maximum holding strength.

Video: Official Command Brand video demonstrating how to use Command Indoor and Outdoor Hooks, covering surface preparation, application, and removal.

Instrucciones de funcionamiento

Each Command Large Utility Hook can hold up to 5 pounds. They are suitable for a variety of items and surfaces.

Image illustrating various surfaces where Command hooks can be used, including painted walls, metal, painted concrete, laminate & finished wood, tile, and smooth surfaces & glass. It also lists surfaces to avoid like wallpaper and textured walls.

Image: A visual guide showing compatible surfaces for Command hooks (painted walls, metal, painted concrete, laminate & finished wood, tile, smooth surfaces & glass) and incompatible surfaces (wallpaper, fabric, textured walls, brick, rough surfaces).

  • Usos recomendados: Hanging clipboards, brushes, dog leashes, kitchen utensils, home decor, accessories, and lightweight coats.
  • Superficies: Painted walls, finished wood, painted concrete cinder blocks, laminate, glass, metal, and tiles.
  • Surfaces to Avoid: Wallpaper, fabric, textured walls, brick, or rough surfaces.
Image showing a kitchen scene with multiple Command hooks holding various kitchen tools and a mesh bag of fruit, highlighting damage-free hanging and decorating.

Image: A kitchen wall with several Command hooks holding kitchen items and a bag of fruit, demonstrating practical, damage-free organization.

Mantenimiento

Command hooks require minimal maintenance. To clean the hooks, simply wipe them with a damp cloth. Avoid using harsh chemicals or abrasive cleaners, as these may damage the plastic or affect the adhesive properties if they come into contact with the strips.

Proceso de eliminación

To remove Command hooks without damaging your surfaces, follow these instructions carefully:

  1. Lightly hold the top of the hook.
  2. Slowly pull the adhesive strip straight down towards the floor. Do not pull the strip toward you or at an angle, as this may cause damage to the surface.
  3. Continue pulling the strip until the hook releases from the wall. The strip will stretch up to several inches.
Image showing hands pulling an adhesive strip straight down from a wall to remove a Command hook, demonstrating the clean removal process.

Image: A close-up of hands pulling the tab of a Command adhesive strip downwards, illustrating the proper technique for damage-free removal.

You can reuse your hook with new Command Refill Strips.

Solución de problemas

Hook Not Sticking

  • Ensure the surface was cleaned with rubbing alcohol only, not household cleaners or water.
  • Verify the surface is smooth and not textured, wallpapered, or fabric.
  • Confirm the indoor temperature is within the recommended range (50°F to 105°F).
  • Ensure you waited 1 hour after application before hanging items.
  • Check that the weight of the item does not exceed 5 pounds.

Strip Breaks During Removal

If the adhesive strip breaks during removal, it may be due to pulling it too quickly or at an angle. To remove the remaining strip:

  • Gently slide a piece of dental floss or fishing line behind the hook/strip.
  • Work the floss/line back and forth in a sawing motion to separate the adhesive from the wall.

Presupuesto

MarcaDominio
Número de modelo17003-MPES
ColorBlanco
MaterialPlástico
Tipo de montajeMontaje en pared
Capacidad máxima de peso5 Pounds (2.2 kg) per hook
Componentes incluidos14 Hooks, 16 Strips
Dimensiones del artículo2.11 x 3.9 x 7.15 pulgadas
Peso del artículo6.08 onzas

Garantía y soporte

Los productos industriales y ocupacionales de 3M están diseñados, etiquetados y empaquetados para su venta a clientes industriales y ocupacionales capacitados para su uso en el lugar de trabajo. A menos que se indique específicamente lo contrario en el empaque o la documentación correspondiente del producto, estos productos no están diseñados, etiquetados ni empaquetados para su venta ni para su uso por parte de los consumidores (por ejemplo, para uso doméstico, personal, en escuelas primarias o secundarias, recreativo/deportivo u otros usos no descritos en el empaque o la documentación correspondiente del producto). Deben seleccionarse y usarse de conformidad con las normas y regulaciones de salud y seguridad aplicables (por ejemplo, US OSHA, ANSI), así como con toda la documentación del producto, las instrucciones de uso, las advertencias y otras limitaciones. El usuario debe tomar las medidas requeridas en virtud de cualquier aviso de retirada, acción de campo u otro aviso de uso del producto. El uso indebido de los productos industriales y ocupacionales de 3M puede provocar lesiones, enfermedades, la muerte o daños materiales. Para obtener ayuda con la selección y el uso del producto, consulte a su profesional de seguridad en el lugar de trabajo, higienista industrial u otro experto en la materia. Para obtener más información sobre el producto, visite www.3M.com.

© 2026 Command Brand. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.