1. Introducción
This manual provides essential information for the safe and efficient operation of your Luminous Solar Hybrid 850 Va Home UPS. Please read these instructions carefully before installation and use, and retain them for future reference.
2. Instrucciones de seguridad
- Asegúrese de que haya una conexión a tierra adecuada para todas las conexiones eléctricas.
- No abra el SAI casing unless you are a qualified service technician. High voltages están presentes en el interior.
- Keep the UPS away from water, moisture, and flammable materials.
- Asegúrese de que haya una ventilación adecuada alrededor de la unidad para evitar el sobrecalentamiento.
- Connect batteries with correct polarity (+ to + and - to -). Incorrect connection can cause damage.
- Always disconnect power before performing any maintenance or connections.
3. Producto terminadoview
The Luminous Solar Hybrid 850 Va Home UPS is designed to provide uninterrupted power to your home by utilizing both solar energy and grid power. It features an inbuilt 30 Amp PWM charge controller for efficient solar charging.
3.1 Disposición del panel trasero
The image below illustrates the rear panel of the Luminous Solar Hybrid 850 Va Home UPS, highlighting key connection points and controls.
Descripción de la imagen: This image displays the rear panel of the Luminous Solar Hybrid 850 Va Home UPS. From left to right, it shows the Mains Fuse, an Output socket (multi-pin type), a red cable (likely for battery connection), a cooling fan grille, a label indicating "Luminous Solar Home UPS 850-24V" with a serial number, a switch for ECO/UPS mode, a switch for I-CHG (charging current), a battery type selection switch (Tubular, Flat Plate, GEL/VRLA), and DC load terminals for solar panel input and battery connection. A warning label advises observing correct polarity for solar battery and load terminals. The panel also indicates "PANEL UPTO 1800W/24V".
- Fusible de red: Protects the unit from overcurrent from the mains input.
- Zócalo de salida: Connect your home appliances to this socket.
- Ventilador de enfriamiento: Garantiza una disipación de calor adecuada para un rendimiento óptimo.
- ECO/UPS Mode Switch: Selects between ECO mode (wider voltage window, energy saving) and UPS mode (narrower voltage window, constant power supply).
- I-CHG Switch: Controls the charging current.
- Selección del tipo de batería: Allows selection for Tubular, Flat Plate, or GEL/VRLA batteries to optimize charging. (Note: Remove cover for selection as indicated on the panel).
- DC Load Terminals: Connections for solar panels (PV+ / PV-) and battery (BAT+ / BAT-). Observe correct polarity.
4. Configuración e instalación
4.1 Desembalaje
Carefully remove the UPS from its packaging. Inspect for any signs of damage during transit. Retain packaging for future transport or service.
4.2 Colocación
Place the UPS in a well-ventilated area, away from direct sunlight, heat sources, and moisture. Ensure there is sufficient space around the unit for air circulation, especially around the cooling fan.
4.3 Conexión de la batería
- Ensure the UPS is switched OFF and disconnected from the mains.
- Connect the positive (+) terminal of the battery to the BAT+ terminal on the UPS.
- Connect the negative (-) terminal of the battery to the BAT- terminal on the UPS.
- Importante: Observe correct polarity. Incorrect connection will damage the unit.
- Select the appropriate battery type (Tubular, Flat Plate, or GEL/VRLA) using the switch on the rear panel. You may need to remove a cover to access this switch.
4.4 Conexión del panel solar
The UPS supports solar panels up to 1800W/24V.
- Ensure the UPS is switched OFF and disconnected from the mains.
- Connect the positive (+) terminal of your solar panel array to the PV+ terminal on the UPS.
- Connect the negative (-) terminal of your solar panel array to the PV- terminal on the UPS.
- Importante: Asegúrese de que el panel solar vol.tage and current are within the specified limits for the 30 Amp PWM charge controller. Observe correct polarity.
4.5 Mains and Load Connection
- Connect the mains power cord to a grounded wall outlet.
- Connect your appliances (load) to the Output socket on the rear panel of the UPS.
- Do not overload the UPS beyond its rated capacity of 850VA.
5. Instrucciones de funcionamiento
5.1 Encendido / Apagado
- Para encender: After all connections are secure, switch on the UPS using the main power switch (if present, typically on the front or side).
- Para apagar: Switch off the UPS, then disconnect it from the mains and battery.
5.2 Mode Selection (ECO/UPS)
Use the ECO/UPS switch on the rear panel to select the desired operating mode:
- Modo SAI: Provides a stable output voltage within a narrow range (180V-260V typically), ideal for sensitive electronic equipment.
- Modo ecologico: Operates with a wider input voltage window (100V-290V), conserving battery power by switching to battery backup only when the mains voltage goes outside this wider range.
5.3 Carga
The Luminous Solar Hybrid UPS intelligently charges the battery:
- If solar energy is available and sufficient, the battery will be charged primarily from the solar panels.
- If solar energy is insufficient or unavailable, the UPS will charge the battery from the mains/grid.
- Adjust the I-CHG switch to control the charging current if necessary, based on battery specifications.
6. Mantenimiento
- Limpieza: Keep the UPS clean and free from dust. Use a dry cloth to wipe the exterior. Ensure ventilation openings are not blocked.
- Comprobación de la batería: Regularly inspect battery terminals for corrosion. Clean them if necessary. For flooded batteries, check electrolyte levels periodically and top up with distilled water as required.
- Conexiones: Revise periódicamente todas las conexiones eléctricas para asegurarse de que estén firmes y seguras.
- Ambiente: Asegúrese de que el entorno operativo permanezca dentro de los rangos de temperatura y humedad recomendados.
7. Solución de problemas
| Problema | Posible causa | Solución |
|---|---|---|
| UPS not turning on. | No mains power; Battery not connected or discharged; Main switch off. | Check mains supply; Connect and charge battery; Turn on main switch. |
| No output from UPS. | Overload; Output fuse blown; UPS in fault mode. | Reduce load; Check/replace output fuse; Restart UPS. |
| La batería no se carga. | Mains power absent; Solar panels not connected or insufficient sunlight; Battery type incorrect. | Check mains supply; Verify solar panel connections and sunlight; Ensure correct battery type selection. |
| UPS beeping continuously. | Overload; Low battery; Internal fault. | Reduce load; Allow battery to charge; Contact customer support if problem persists. |
8. Especificaciones
| Característica | Detalle |
|---|---|
| Marca | Luminoso |
| Nombre del modelo | LU-03 (Model Number: Solar 850) |
| Capacidad nominal | 850 VA |
| Tipo de onda | De onda sinusoidal pura |
| Volumentage Window (ECO Mode) | 100 V - 290 V |
| Inbuilt Charge Controller | 30 Amp Modulación por ancho de pulso (PWM) |
| Salida de carga de CC | 12 V upto 20 Amp |
| Max. Solar Panel Input | 1800W / 24V |
| Frecuencia | 50 Hz |
| Dimensiones (L x An x Al) | 37.5L x 31.5W x 13.5H Centímetros |
| Peso | 11.5 kilogramos |
| Fuente de poder | Funciona con pilas |
| Usos recomendados | Hogar |
| Contenido de la caja | 1-Piece Solar Hybrid 850 Va Home UPS |
9. Garantía y soporte
Your Luminous Solar Hybrid 850 Va Home UPS comes with a 24 meses de garantía del fabricante a partir de la fecha de compra.
For technical assistance, service, or warranty claims, please contact Luminous Power TECHNOLOGIES Pvt. Ltd. at the details below:
- Fabricante: Luminous Power TECHNOLOGIES Pvt. Ltd.
- DIRECCIÓN: VILLAGE DEV NAGAR PO GAGRET TEHAMB DISTT. UNA HIMACHAL PRADESH - 177201
- Atención al cliente: 18001033039
Please have your product model number (Solar 850) and serial number ready when contacting support.