Airam LED Cabinet Lamp Manual de instrucciones de 1.2W

1. Introducción

This manual provides essential instructions for the safe and efficient use of your Airam LED Cabinet Lamp 1.2W. This battery-operated lamp features a PIR motion sensor, automatically illuminating when motion is detected, making it ideal for cabinets, drawers, and other enclosed spaces. Please read this manual thoroughly before installation and operation.

2. Configuración

2.1 Contenido del paquete

Antes de continuar, asegúrese de que todos los componentes estén presentes:

• Airam LED Cabinet Lamp 1.2 W
• Mounting hardware (screws or adhesive strips, typically included in packaging)

Figure 1: Airam LED Cabinet Lamp in its retail packaging, showing the lamp and typical mounting accessories.

2.2 Instalación de la batería

The Airam LED Cabinet Lamp requires 4 x AA 1.5V batteries (not included).

1. Locate the battery compartment cover on the back or side of the lamp.
2. Deslice o desenganche la tapa para abrir el compartimento.
3. Insert 4 AA batteries, ensuring correct polarity (+ and - terminals match the markings inside the compartment).
4. Cierre bien la tapa del compartimento de la batería.

2.3 Montaje de la Lamp

El lamp can be mounted using screws or adhesive strips, depending on the included hardware and your preference. Choose a location where the motion sensor has a clear line of sight to the area where movement is expected (e.g., inside a cabinet door, above a drawer).

Figura 2: Frente view of the Airam LED Cabinet Lamp, highlighting the central motion sensor.

Using Screws (if applicable):

1. Mark the desired mounting position.
2. Drill pilot holes if necessary, matching the lampOrificios de montaje de
3. Asegurar el lamp utilizando los tornillos proporcionados.

Using Adhesive Strips (if applicable):

1. Limpie completamente la superficie de montaje para asegurarse de que esté seca y libre de polvo o grasa.
2. Peel the protective backing from the adhesive strips.
3. Presione firmemente la lamp onto the desired surface for at least 30 seconds.

3. Operación

The Airam LED Cabinet Lamp is designed for automatic operation using its integrated PIR (Passive Infrared) motion sensor.

1. Once batteries are installed and the lamp is mounted, it will enter standby mode.
2. When the PIR motion sensor detects movement within its range (e.g., opening a cabinet door or drawer), the LED lights will automatically turn on.
3. El lamp will remain illuminated for approximately 25 seconds after motion is detected.
4. If no further motion is detected within this period, the lamp will automatically turn off to conserve battery power.
5. If continuous motion is detected, the lamp will remain on until motion ceases for 25 seconds.

Nota: Ensure the motion sensor is not obstructed for optimal performance.

4. Mantenimiento

4.1 Reemplazo de batería

When the light output diminishes or the lamp stops functioning, it is time to replace the batteries. Refer to section 2.2 Instalación de la batería para obtener instrucciones detalladas.

• Reemplace siempre las 4 pilas AA al mismo tiempo.
• No mezcle baterías viejas y nuevas, o diferentes tipos de baterías.
• Deseche las baterías usadas de manera responsable de acuerdo con las regulaciones locales.

4.2 Limpieza

El lamp is constructed from polycarbonate and ABS plastic. To clean the lamp:

• Limpie la superficie con un paño suave, seco o ligeramente húmedo.amp paño.
• Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the plastic finish or the sensor.
• Ensure no liquid enters the battery compartment or sensor area.

5. Solución de problemas

6. Especificaciones

7. Garantía y soporte

Specific warranty information may vary by region and retailer. Please refer to your purchase documentation or contact your point of sale for details regarding warranty coverage.

For technical support or further assistance, please contact the manufacturer, Bot Lighting, or your retailer. Keep your purchase receipt as proof of purchase.