M-Wave Bicycle Computer Cicli Bonin_CVC911 User Manual

1. Introducción

This manual provides comprehensive instructions for the M-Wave Bicycle Computer, model Cicli Bonin_CVC911. It covers installation, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your device. Please read this manual thoroughly before using the product.

Image 1: M-Wave Bicycle Computer head unit, yellow model.

2. Información de seguridad

Always prioritize safety when cycling. Ensure the computer is securely mounted and does not obstruct your view or control of the bicycle. Do not attempt to operate the computer while riding in traffic or hazardous conditions. Keep batteries out of reach of children. Dispose of batteries responsibly according to local regulations.

3. Contenido del paquete

Verifique que todos los componentes estén presentes en el paquete:

• M-Wave Bicycle Computer Head Unit
• Sensor de velocidad inalámbrico
• Imán de rueda
• Mounting Bracket for Handlebar/Stem
• Zip Ties for Sensor and Bracket
• Baterías (preinstaladas o separadas)
• Manual de instrucciones

4. Configuración

4.1 Instalación de la batería

The M-Wave Bicycle Computer uses alkaline batteries. If not pre-installed, open the battery compartment on the back of the head unit and the speed sensor. Insert the batteries with correct polarity, observing the '+' and '-' markings, and securely close the compartments.

4.2 Sensor and Magnet Mounting

Attach the wireless speed sensor to the front fork using the provided zip ties. Position the wheel magnet on a spoke so that it passes within 2mm of the sensor when the wheel rotates. Ensure the magnet and sensor are aligned for reliable signal transmission.

4.3 Computer Mounting

Mount the computer head unit to your handlebar or stem using the provided bracket and zip ties. Ensure it is firmly secured and visible without obstructing your view o controles.

Imagen 2: Lateral view of the M-Wave Bicycle Computer, illustrating its compact design and potential mounting points.

4.4 Ajustes iniciales

Upon first use or after battery replacement, you will need to set up the computer. This typically involves:

1. Diámetro de la rueda: Refer to your bicycle tire's sidewall for the circumference or use a measurement chart. Input this value into the computer for accurate speed and distance readings.
2. Unidades: Select your preferred units for speed (km/h or mph) and temperature (C° or F°).
3. Tiempo: Establecer la hora actual.

Consult the on-screen prompts and use the 'SET' and 'MODE' buttons for navigation and selection.

5. Instrucciones de funcionamiento

The M-Wave Bicycle Computer features 14 functions. Use the 'MODE' button to cycle through different display modes and the 'SET' button for adjustments within a mode.

Image 3: Product packaging showing the 14 functions of the M-Wave Bicycle Computer.

• Velocidad actual: Muestra tu velocidad de ciclismo en tiempo real.
• Velocidad media: Shows the average speed for your current ride.
• Velocidad máxima: Registra la velocidad más alta alcanzada durante tu recorrido.
• Distancia (DST): Displays the distance covered during your current ride.
• Total Distance (ODO): Shows the accumulated total distance.
• Tiempo de viaje: Realiza un seguimiento de la duración de tu viaje actual.
• Reloj: Muestra la hora actual.
• Temperatura: Shows the ambient temperature in Celsius or Fahrenheit.
• Contador de calorías: Calcula las calorías quemadas durante el recorrido.
• CO2 Savings: Calculates estimated CO2 savings compared to driving.
• Inicio/parada automática: The computer automatically starts recording when you begin cycling and pauses when you stop.
• Speed Tendency/Comparison: Indicates if your current speed is higher or lower than your average speed.

6. Mantenimiento

6.1 Limpieza

Limpie la computadora y el sensor con un paño suave.amp cloth. Do not use abrasive cleaners or solvents. The unit is waterproof, but avoid submerging it for extended periods.

6.2 Reemplazo de batería

When the display becomes dim or functions become erratic, it's time to replace the batteries. Follow the battery installation steps outlined in Section 4.1, ensuring correct polarity. Resetting initial settings may be required after battery replacement.

7. Solución de problemas

If your M-Wave Bicycle Computer is not functioning as expected, consider the following:

• Sin visualización de velocidad:
  • Check the distance between the sensor and magnet. It should be no more than 2mm.
  • Asegúrese de que el sensor y el imán estén alineados correctamente.
  • Verify that the sensor battery is not depleted.
  • Confirm the computer head unit battery is not depleted.
• Lecturas inexactas:
  • Re-check the wheel diameter setting.
  • Asegúrese de que el sensor y el imán estén montados de forma segura y no se muevan.
• La pantalla está en blanco:
  • Replace the computer head unit battery.
  • Asegúrese de que la batería esté insertada con la polaridad correcta.
• Los botones no responden:
  • Intente quitar y volver a insertar la batería para realizar un reinicio suave.

8. Especificaciones

9. Garantía y soporte

For warranty information and technical support, please refer to the M-Wave official webSitio web o contacte a su vendedor. Conserve su recibo de compra como comprobante.