Introducción
This manual provides essential information for the safe and efficient operation, installation, and maintenance of your PEDROLLO JSWm/2CX self-priming water pump. Please read these instructions carefully before installation or use and retain them for future reference.
Figura 1: PEDROLLO JSWm/2CX Self-Priming Water Pump. This image shows the blue-colored pump unit with its motor housing and pump body, designed for efficient water transfer.
Información de seguridad
Observe siempre las siguientes precauciones de seguridad para evitar lesiones o daños a la bomba:
- Ensure the pump is installed by a qualified professional.
- Desconecte la alimentación antes de realizar cualquier mantenimiento o servicio.
- No opere la bomba con líquidos inflamables o corrosivos.
- Proteja la bomba de temperaturas bajo cero.
- Asegúrese de que la conexión eléctrica esté correctamente conectada a tierra.
Producto terminadoview
The PEDROLLO JSWm/2CX is a self-priming centrifugal pump designed for reliable water transfer. It is suitable for pumping clean water and liquids that are not chemically aggressive to the pump's components. Its self-priming capability allows it to draw water even when air is present in the suction line, making it ideal for domestic water supply, small to medium autoclave tank systems, and garden irrigation.
Características principales:
- Self-priming design for efficient operation.
- Suitable for clean water and non-aggressive liquids.
- Robust construction with stainless steel components.
- Designed for continuous duty in domestic and garden applications.
Configuración e instalación
Proper installation is crucial for the pump's performance and longevity. Consult a qualified technician for installation.
- Ubicación: Install the pump in a dry, well-ventilated area, protected from direct sunlight and freezing temperatures. Ensure adequate space for maintenance.
- Montaje: Securely fasten the pump to a stable, level surface using appropriate bolts to minimize vibration.
- Tubería:
- Use pipes of adequate diameter to minimize friction losses.
- Ensure all connections are airtight, especially on the suction side, to prevent air ingress.
- Instale una válvula de pie con un filtro en el extremo del tubo de succión para evitar que entren residuos en la bomba y para mantenerla cebada.
- Install a gate valve on both the suction and discharge sides for isolation during maintenance.
- Conexión eléctrica:
- Connect the pump to a suitable power supply (220-230V, 50Hz) as indicated on the motor's data plate.
- Ensure the electrical circuit is protected by a residual current device (RCD) and an appropriately rated circuit breaker.
- Verify proper grounding according to local electrical codes.
- Cebado: Before initial startup, completely fill the pump casing and the suction line with clean water through the priming port. This is essential for self-priming pumps to initiate operation.
Instrucciones de funcionamiento
- Puesta en marcha inicial: After installation and priming, open the discharge valve fully. Switch on the power supply. The pump should start and begin to draw water.
- Operación continua: Monitor the pump for unusual noises or vibrations. Ensure the pump is not running dry, as this can cause severe damage.
- Cerrar: To stop the pump, switch off the power supply. If the pump is part of an automatic system (e.g., with a pressure switch), it will start and stop automatically based on demand.
- Límites de temperatura:
- Liquid temperature: up to +40 °C.
- Ambient temperature: -10 °C to +40 °C.
Mantenimiento
Regular maintenance ensures optimal performance and extends the pump's lifespan. Always disconnect power before maintenance.
- Controles periódicos: Inspect the pump and piping for leaks, corrosion, or damage.
- Limpieza del colador: Periodically clean the foot valve strainer to prevent blockages and maintain flow.
- Winterización: In areas prone to freezing, drain the pump completely and store it in a warm, dry place, or insulate it adequately to prevent damage from ice expansion.
- Inspección del motor: Asegúrese de que las aletas de enfriamiento del motor estén libres de polvo y residuos para evitar el sobrecalentamiento.
Solución de problemas
| Problema | Posible causa | Solución |
|---|---|---|
| La bomba no arranca | No power supply; Motor overload; Seized impeller. | Check power connection and circuit breaker; Reset thermal overload; Contact service technician. |
| La bomba funciona pero no sale agua | Pump not primed; Air leak in suction line; Foot valve clogged; Suction lift too high. | Re-prime the pump; Check all suction connections for leaks; Clean foot valve strainer; Reduce suction lift if possible. |
| Flujo o presión reducidos | Partial blockage in piping; Worn impeller; Air in system. | Inspect and clear piping; Contact service technician for impeller replacement; Bleed air from system. |
| Ruido o vibración excesivos | Cavitation (air in water); Loose mounting; Bearing wear. | Check for air leaks and ensure proper priming; Tighten mounting bolts; Contact service technician. |
Presupuesto
| Parámetro | Valor |
|---|---|
| Modelo | JSWm/2CX |
| Marca | Pedrollo |
| Potencia (CV) | 1 CV |
| Volumentage / Frecuencia | 220-230 V / 50 Hz |
| Caudal máximo | 70 litros por minuto |
| Rango de temperatura del líquido | Hasta +40 °C |
| Rango de temperatura ambiente | -10 °C a +40 °C |
| Material | Stainless Steel (pump body components) |
| ASIN | B07HMZ2DKQ |
| Código de artículo internacional | 08052230012515 |
Note: The specification for "Power: 220 Watts" found in some product listings may refer to a specific component or a different metric. The pump's performance is rated at 1 HP.
Garantía y soporte
For warranty information, technical support, or spare parts, please contact your authorized Pedrollo dealer or visit the official Pedrollo webSitio. Conserve su recibo de compra como comprobante de compra.
Fabricante: PEDROLLO