1. Introducción
This manual provides detailed instructions for the assembly, operation, and maintenance of your Antec NX410 ATX Mid-Tower Case. Please read this manual thoroughly before beginning installation to ensure proper setup and to maximize the performance and longevity of your system.
Figure 1.1: Antec NX410 ATX Mid-Tower Case (Black)
2. Características principales
- Refrigeración avanzada: Pre-installed with 2 x 140mm ARGB fans in the front and 1 x 120mm ARGB fan in the rear for efficient airflow.
- Panel lateral de vidrio templado: A full-side view tempered glass panel allows for showcasing internal components and RGB lighting.
- Flujo de aire optimizado: Features a grid front panel design to enhance air intake and maintain optimal temperatures.
- Soporte de placa base: Compatible con factores de forma de placa base ATX, Micro-ATX e ITX.
- Ample Expansion: Supports various storage configurations and large graphics cards (up to 335mm) and CPU coolers (up to 168mm).
3. Configuración e instalación
3.1 Preparación del caso
Before installing components, ensure the case is placed on a stable, flat surface. The tempered glass side panel can be easily opened via a magnetic latch for access to the interior.
Figure 3.1: Internal Component Layout and Compatibility
3.2 Instalación de la placa base
The NX410 supports ATX, Micro-ATX, and ITX motherboards. Install standoffs as required by your motherboard's form factor before mounting the motherboard.
3.3 Soporte de ventilador y radiador
The case comes with pre-installed ARGB fans. Additional fans or radiators can be installed as follows:
- Frente: Up to 3 x 120mm or 3 x 140mm fans (up to 360mm radiator).
- Arriba: Up to 2 x 120mm or 2 x 140mm fans (up to 280mm radiator).
- Trasero: 1 x 120mm fan (up to 120mm radiator).
Figure 3.2: Fan and Radiator Configuration
Important Fan Connection Note:
Figure 3.3: Fan Installation Warning
- If you connect the major fan and other fans but do not connect the major fan to the motherboard, other fans will not function.
- The fan kit does not work in sync with the motherboard ARGB function unless properly connected.
3.4 Instalación de la unidad de almacenamiento
The case provides bays for 3.5-inch HDDs and 2.5-inch SSDs. Refer to the internal layout diagram (Figure 3.1) for specific mounting locations.
3.5 Instalación de la unidad de fuente de alimentación (PSU)
The PSU mounts at the rear bottom of the case. Ensure the PSU length does not exceed 165mm for optimal fit and cable management.
4. Funcionamiento de las características del estuche
4.1 Front Panel I/O Ports
The top front panel provides convenient access to essential ports and controls:
- Botón de encendido
- Botón de control LED
- USB 3.0 x 1
- USB 2.0 x 2
- HD-AUDIO (Headphone and Microphone jacks)
Figure 4.1: Front Panel I/O Ports
4.2 Control de iluminación ARGB
Use the dedicated LED Control Button on the front panel to cycle through various ARGB lighting effects and colors for the pre-installed fans. This allows for customization of your system's aesthetic.
Figure 4.2: LED Control Button
5. Mantenimiento
5.1 Limpieza de los filtros de polvo
The Antec NX410 features a fine mesh front panel and a magnetic dust filter on the top panel to prevent dust buildup. Regularly remove and clean these filters to maintain optimal airflow and cooling performance.
Figure 5.1: Fine Mesh Front Panel
5.2 Accessing Internal Components
The tempered glass side panel is secured with a magnetic latch, allowing for tool-less access to the internal components for upgrades, cleaning, or troubleshooting. Gently pull the handle to open the panel.
6. Solución de problemas
- El sistema no se enciende: Ensure all power cables (24-pin ATX, 8-pin CPU, GPU PCIe) are securely connected to the motherboard, graphics card, and power supply. Verify the power supply switch is in the 'ON' position.
- Los ventiladores no giran/el RGB no funciona: Check fan connections to the motherboard or fan controller. Ensure the LED control button is pressed to cycle through modes. Refer to Figure 3.3 for proper fan wiring.
- Problemas de sobrecalentamiento: Confirm all case fans are installed correctly and spinning. Clean dust filters regularly. Ensure proper thermal paste application on the CPU cooler.
- Los puertos USB no funcionan: Verify the USB headers from the front panel are correctly connected to the motherboard.
7. Especificaciones
| Característica | Detalle |
|---|---|
| Marca | Antec |
| Nombre del modelo | NX410 |
| Tipo de caso | Torre Media |
| Compatibilidad de la placa base | ATX, Micro-ATX, ITX |
| Dimensiones (D x W x H) | 15.35" de profundidad x 8.27" de ancho x 19.09" de alto |
| Material | Vidrio templado, acero |
| Ventiladores preinstalados | 2 x 140 mm ARGB (delantero), 1 x 120 mm ARGB (trasero) |
| Altura máxima del enfriador de CPU | 168 mm |
| Longitud máxima de GPU | 335 mm |
| Longitud máxima de la fuente de alimentación | 165 mm |
| Ranuras de expansión | 7 |
| Puertos de E/S | Power, LED Control Button, USB 3.0 x 1, USB 2.0 x 2, HD-AUDIO |
| Factor de forma del disco duro | 3.5 pulgadas |
| Internal Bays Quantity | 2 (3.5" HDD / 2.5" SSD Convertible), 3 (2.5" SSD) |
8. Garantía y soporte
The Antec NX410 ATX Mid-Tower Case comes with a 2 año de garantía. For technical support, troubleshooting assistance, or warranty claims, please visit the official Antec webSitio web o contacte con el departamento de atención al cliente. Conserve su comprobante de compra para validar la garantía.