JMT ZD850 850mm Hexacopter Frame Kit Instruction Manual

1. Introducción

This manual provides detailed instructions for the assembly, maintenance, and specifications of the JMT ZD850 850mm 6-Axle Full Carbon Fiber Hexacopter Frame Kit. This product is designed for DIY FPV aircraft enthusiasts and requires assembly. Please read these instructions carefully before beginning assembly to ensure correct and safe construction.

2. Producto terminadoview

The JMT ZD850 is an 850mm diagonal wheelbase hexacopter frame kit constructed from full carbon fiber. It features foldable arms and an unfoldable landing gear system, designed for stability and portability.

Características principales:

• 850mm Diagonal Wheelbase: Supports up to 16-inch propellers.
• 20mm Carbon Tube Arms: Designed for strength and rigidity.
• Aluminum Folding Mechanism: Permite un almacenamiento y transporte compacto.
• 8-Hole Motor Mount: Compatible with a wide range of motors.
• Large Center Plate: 245mm x 180mm with 35mm height for electronics integration.
• Robust Landing Gear: 16mm carbon tube tripod, 350mm height, 500mm crossbar for stable grounding, supported by double-tube carbon fiber capable of bearing over 50kg.
• PTZ Board Compatibility: Hook head with 10x330mm carbon tube for flexible PTZ (Pan-Tilt-Zoom) camera mounting.

Figure 2.1: Fully assembled JMT ZD850 hexacopter, showcasing the frame, motors, and propellers (electronics not included in kit).

3. Instrucciones de montaje

The JMT ZD850 is provided as a frame kit and requires complete assembly. No assembly tools are included. You will need a 2.5mm hex wrench, a 2.0mm hex wrench or screwdriver, and a 5.5mm sleeve. A complete set of screwdriver tools is recommended.

Figure 3.1: All components included in the JMT ZD850 Hexacopter Frame Kit, prior to assembly.

3.1. Required Tools (Not Included):

• Llave hexagonal de 2.5 mm
• 2.0mm Hex Wrench or Screwdriver
• Manga de 5.5 mm
• (Recommended) Complete set of precision screwdrivers

3.2. Montaje paso a paso:

1. Prepare the Center Plates: Identify the bottom (3.0mm) and upper (1.5mm) center plates. Attach the necessary standoffs and mounting hardware to the bottom plate as indicated in the kit.
2. Assemble the Arms: Insert the 20mm carbon tube arms into the aluminum folding mechanisms. Secure them using the nylon clamps. Ensure all connections are tight but do not overtighten to avoid damaging the carbon fiber.
3. Attach Arms to Center Plate: Mount the assembled arms to the main center plate using the provided hardware. The arms are designed with an upturned 5-degree angle.
4. Install Motor Mounts: Attach the 8-hole motor mounts to the ends of each carbon fiber arm. These mounts are compatible with various motor sizes.
5. Construct the Landing Gear: Assemble the tripod landing gear using the 16mm carbon tubes for the main legs and the 10mm carbon tubes for support. The tripod crossbar is 500mm wide, and the height is 350mm. Ensure the double-tube carbon fiber supports are correctly installed for maximum stability.
6. Colocar el tren de aterrizaje: Secure the assembled landing gear to the bottom of the main center plate.
7. Install PTZ Board Hook Head: Attach the 10x330mm carbon tube hook head for the PTZ board to the designated area on the frame. This allows for flexible camera mounting.
8. Inspección final: After all components are assembled, carefully inspect all screws, bolts, and connections to ensure they are secure. Verify that all carbon fiber tubes are properly seated and free from damage.

Figure 3.2: The JMT ZD850 Hexacopter frame fully assembled, ready for electronics installation.

4. Consideraciones operativas

This manual covers the assembly of the JMT ZD850 frame kit. The operational aspects of the hexacopter, including flight control, motor calibration, and propeller installation, depend on the specific electronic components (motors, ESCs, flight controller, battery, receiver, etc.) chosen and installed by the user. Please refer to the instruction manuals provided with your chosen electronic components for their proper installation, configuration, and safe operation.

Componentes recomendados (no incluidos):

• 3508-380kv motors
• 6s 22.2v 25c Lithium battery
• 1555/1547 15-inch CW/CCW propellers

5. Mantenimiento

Regular maintenance is crucial for the longevity and safe operation of your hexacopter frame.

• Comprobaciones previas al vuelo: Before each use, inspect all carbon fiber tubes, aluminum folding parts, and nylon clamps for any signs of damage, cracks, or wear.
• Inspección de sujetadores: Periodically check all screws, bolts, and connections for tightness. Vibrations during flight can cause fasteners to loosen over time.
• Limpieza: Keep the frame clean from dirt, dust, and debris. Use a soft, dry cloth. Avoid harsh chemicals that could damage the carbon fiber or other materials.
• Almacenamiento: Store the frame in a cool, dry place, away from direct sunlight and extreme temperatures. The foldable arms allow for more compact storage.
• Reparación de daños: In case of damage to carbon fiber components, replace the affected part immediately. Do not attempt to fly with a damaged frame.

6. Solución de problemas

This section addresses common issues related to the frame assembly. For issues related to electronic components, refer to their respective manuals.

7. Especificaciones

8. Garantía y soporte

Specific warranty information for the JMT ZD850 Hexacopter Frame Kit is not provided in the product details. For any warranty claims or technical support, please contact the retailer or manufacturer directly. Ensure you retain your proof of purchase.