LightmaXX LED Blinder 2 - Manual del usuario

1. Introducción

Thank you for choosing the lightmaXX LED Blinder 2. This professional stage lighting fixture is designed to provide powerful and versatile illumination for various applications. Featuring two 50-watt warm white COB LEDs, DMX control, and a strobe function, it offers robust performance and flexible integration into your lighting setup. Please read this manual thoroughly before operation to ensure safe and optimal use of your device.

2. Instrucciones de seguridad

Observe siempre las siguientes precauciones de seguridad para evitar descargas eléctricas, incendios o lesiones:

• Este dispositivo es sólo para uso profesional.
• Asegúrese de que la fuente de alimentación voltage coincide con los requisitos del dispositivo.
• No exponga el dispositivo a la lluvia ni a la humedad.
• Siempre conecte el dispositivo a una toma de corriente con conexión a tierra.
• No abra la carcasa. No contiene piezas que el usuario pueda reparar. Encargue cualquier reparación a personal cualificado.
• Evite la exposición directa de los ojos a la fuente de luz.
• Asegúrese de que haya una ventilación adecuada alrededor de la unidad para evitar el sobrecalentamiento.
• Always secure the device with a safety cable when mounting overhead.
• Desconecte de la alimentación antes de limpiar o realizar mantenimiento.

3. Producto terminadoview

The lightmaXX LED Blinder 2 features a robust design with two powerful COB LEDs and intuitive controls.

Figura 3.1: Frente view of the lightmaXX LED Blinder 2, showing the two illuminated COB LEDs.

Figura 3.2: Frente view of the lightmaXX LED Blinder 2, illustrating the power cable connection point.

Figure 3.3: Rear panel of the lightmaXX LED Blinder 2, detailing the control display, DMX In/Out, Power In/Out, and safety rope attachment point.

Figure 3.4: Close-up of the control panel, showing the digital display and navigation buttons (MENU, UP, DOWN, ENTER).

3.1 Componentes

• 2 x 50W Warm White COB LEDs
• Digital Display and Control Buttons (MENU, UP, DOWN, ENTER)
• DMX In/Out (3-pin XLR)
• Power In/Out (IEC)
• Soporte de montaje ajustable
• Safety Rope Attachment Point

4. Configuración

4.1 Montaje

The lightmaXX LED Blinder 2 comes with a versatile mounting bracket for truss, floor, or stand mounting. Ensure the mounting surface or structure can safely support the weight of the fixture. Always use a safety cable (not included) when mounting the unit overhead to prevent accidental falls.

• Attach the mounting bracket securely to a truss clamp o estar de pie.
• Adjust the angle of the fixture using the side knobs on the bracket.
• Connect a safety cable from the fixture's safety rope attachment point to the mounting structure.

4.2 Conexión de alimentación

Connect the supplied power cable to the "POWER IN" IEC connector on the rear of the unit and then to a suitable grounded power outlet. The "POWER OUT" connector allows for daisy-chaining power to multiple units (check maximum power draw before connecting multiple units).

4.3 Conexión DMX (opcional)

For DMX control, connect a DMX cable from your DMX controller's output to the "DMX IN" port on the blinder. To daisy-chain multiple DMX fixtures, connect a DMX cable from the "DMX OUT" port of the first blinder to the "DMX IN" port of the next fixture in the chain. Terminate the last fixture in the DMX chain with a DMX terminator.

5. Instrucciones de funcionamiento

5.1 Funcionamiento del panel de control

Use the four buttons on the rear panel to navigate the menu and adjust settings:

• MENÚ: Enters the menu or goes back to the previous menu level.
• UP: Scrolls up through menu options or increases a value.
• ABAJO: Scrolls down through menu options or decreases a value.
• ENTRAR: Confirma una selección o ingresa a un submenú.

5.2 DMX Modes and Channel Assignment

The lightmaXX LED Blinder 2 supports 6 DMX channels. Refer to the DMX chart below for specific channel functions. Set the DMX address using the control panel. The default DMX address is A001.

5.3 Modos independientes

The blinder can operate without a DMX controller using its built-in programs or sound-activated mode. Access these modes via the control panel menu.

• Modo automático: Cycles through pre-programmed light sequences.
• Modo activo de sonido: The light reacts to ambient sound via the built-in microphone.
• Atenuador manual: Adjust the brightness of each LED directly from the menu.

6. Mantenimiento

Regular maintenance ensures the longevity and optimal performance of your lightmaXX LED Blinder 2.

• Limpieza: Disconnect the power before cleaning. Use a soft, lint-free cloth to wipe the exterior. For stubborn dirt, a slightly damp Se puede usar un paño. No utilice limpiadores abrasivos ni disolventes.
• Fan and Vent Cleaning: Periodically check and clean the cooling fan and ventilation openings to ensure proper airflow and prevent overheating. Use compressed air to remove dust.
• Inspección de cables: Regularly inspect power and DMX cables for any signs of damage (cuts, frayed wires). Replace damaged cables immediately.
• Almacenamiento: When not in use, store the fixture in a dry, dust-free environment, preferably in its original packaging or a suitable flight case.

7. Solución de problemas

If you encounter issues with your lightmaXX LED Blinder 2, refer to the following common problems and solutions:

If the problem persists after trying these solutions, please contact lightmaXX customer support or your authorized dealer.

8. Especificaciones

9. Garantía y soporte

Specific warranty information for the lightmaXX LED Blinder 2 is not provided in this manual. Please refer to your purchase documentation, the lightmaXX official website, or contact your retailer for details regarding warranty coverage and terms.

For technical support, service, or spare parts inquiries, please contact lightmaXX customer service or your authorized dealer. Ensure you have your model number (LIG0016526-000) and purchase date available when contacting support.

Manufacturer: lightmaXX