LEDVANCE 65636
Sylvania 32ft RGB Flexible Light Strip Starter Kit Instruction Manual
Modelo: 65636 | Marca: LEDVANCE
Información importante de seguridad
- Uso exclusivo en interiores: Este producto está diseñado para uso en interiores y lugares secos. No lo exponga al agua ni a la humedad.
- Seguridad eléctrica: Ensure the power adapter is connected to a suitable power outlet. Do not overload electrical circuits.
- Instrucciones de corte: The LED strips can be cut for customized length. Only cut along the designated markings to avoid damaging the strip.
- Instalación: Desconecte siempre la energía antes de la instalación o el mantenimiento.
- Calor: Do not cover the LED strips with materials that may trap heat, as this can cause overheating.
- Niños: Mantenga el producto y sus componentes fuera del alcance de los niños.
Contenido del paquete
Verifique que todos los componentes estén presentes en su paquete:
- (2) 16.4ft RGB Flexible LED Light Strips
- (1) Fuente de alimentación
- (1) IR Remote Controller (with battery included)
- (20) clips de montaje
Image: Main product image showing the light strips, remote, power adapter, and clips.
Configuración e instalación
- Prepare la superficie: Ensure the installation surface is clean, dry, and smooth for optimal adhesion of the clips.
- Conectar componentes: Connect the LED light strips to the controller, ensuring the arrows on the connectors align. Then, connect the power supply to the controller.
- Funcionalidad de prueba: Before permanent mounting, plug in the power supply and use the remote control to test the light strips. Verify all colors and modes function correctly.
- Customize Length (Optional): If a shorter length is desired, only cut the LED strips along the designated cutting marks (usually indicated by a scissor icon or copper pads). Cutting elsewhere will damage the strip.
- Mount the Strips: Remove the adhesive outer layer from the back of the mounting clips and press firmly for five seconds when mounting. Use the provided clips to secure the light strips in your desired location, such as under cabinets, behind TVs, or along shelves.
- Activar control remoto: Remove the plastic tab from the remote control's battery door to activate the battery.
Image: Step-by-step diagram illustrating how to connect the light strips, identify cutting points, and mount them using clips.
Operación
The Sylvania RGB Flexible Light Strips are controlled using the included IR remote. Ensure the remote is pointed towards the IR receiver on the controller for optimal response.
Funciones del control remoto:
- ENCENDIDO/APAGADO: Power the light strips on or off.
- Selección de colores: Elija entre 16 colores estáticos utilizando los botones de color.
- Atenuación: Adjust the brightness of the selected color or dynamic mode.
- Modos dinámicos: Select from 4 pre-programmed dynamic modes (e.g., Flash, Strobe, Fade, Smooth) to create different lighting effects.
Image: Detailed illustration of the IR remote control, highlighting buttons for power, color selection, dimming, and dynamic modes.
Mantenimiento
- Limpieza: Limpie suavemente las tiras LED con un paño seco y suave. No utilice limpiadores líquidos ni productos abrasivos.
- Esperanza de vida: The LED technology provides a long operational life of up to 30,000 hours under normal use conditions.
- Reemplazo de batería remota: If the remote control becomes unresponsive, replace the CR2025 lithium coin cell battery.
Solución de problemas
| Problema | Posible causa | Solución |
|---|---|---|
| Las luces no se encienden. | Power connection issue, remote battery dead, IR receiver blocked. | Check all connections (power supply, controller, strips). Ensure arrows on connectors align. Replace remote battery. Ensure remote is pointed at the IR receiver without obstruction. |
| El control remoto no responde. | Remote battery dead, remote too far, IR receiver blocked. | Replace remote battery. Ensure remote is within range and pointed directly at the IR receiver. Remove any obstructions between the remote and receiver. |
| Some sections of the light strip are not lighting up. | Damaged section, incorrect cutting. | Inspect the strip for physical damage. If a section was cut incorrectly, it may be permanently damaged. Ensure connections are secure. |
Presupuesto
| Característica | Detalle |
|---|---|
| Número de modelo | 65636 |
| Marca | LEDVANCE (Sylvania) |
| Color | RGB (16 colors) + White |
| Longitud | 32ft (2 x 16.4ft strips) |
| Uso | Solo en interiores |
| Características especiales | Cambio de color, regulable, eficiencia energética |
| Tipo de fuente de luz | CONDUJO |
| Fuente de poder | Eléctrico con cable |
| Tipo de controlador | Control remoto por infrarrojos |
| Volumentage | 12 voltios |
| Quétage | 24 vatios |
| Conectividad | Infrarrojo |
| Material | Plástico |
| Peso del artículo | 10.88 onzas |
| Esperanza de vida | Hasta 30,000 horas |
| Resistencia al agua | No resistente al agua |
| Código Postal | 046135656361 |
Garantía y soporte
This Sylvania LED Flexible Light Strip Starter Kit is backed by a Garantía del fabricante de 1 años.
For technical support, warranty claims, or additional product information, please visit the official LEDVANCE websitio o comuníquese con su departamento de servicio al cliente.
También puedes visitar el Tienda LEDVANCE en Amazon Para más productos e información.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.