Akicon Ultra Quiet Bathroom Exhaust Fan with LED Light

1. Información de seguridad

Lea y comprenda todas las instrucciones antes de comenzar la instalación. El incumplimiento de estas instrucciones podría provocar descargas eléctricas, incendios, daños materiales o lesiones personales.

• Desconecte siempre la alimentación en el panel de servicio antes de cablear o realizar mantenimiento a la unidad.
• Todo el cableado debe cumplir con los códigos y estándares eléctricos locales.
• Esta unidad está diseñada únicamente para ventilación general. No la utilice para extraer materiales y vapores peligrosos o explosivos.
• To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device unless specifically approved for such use.
• Ensure the installation location provides adequate structural support for the fan.

2. Contenido del paquete

Verifique que todos los componentes estén presentes antes de comenzar la instalación:

• Vivienda del ventilador
• Ensamblaje de rejilla
• LED Bulbs (2x)
• Frosted Glass Cover
• Tornillos de montaje
• Manual de instrucciones

Image: Components of the Akicon Bathroom Exhaust Fan.

3. Especificaciones del producto

Image: Key dimensions of the Akicon Bathroom Exhaust Fan.

Image: Detailed housing dimensions and ceiling opening size requirements.

4. Instalación

This fan can be installed with or without attic access. Refer to the appropriate video and steps below.

4.1 Comprobaciones previas a la instalación

• Ensure your soffit or attic has enough space for installation.
• Required opening size: 8-1/2" x 8-5/16".
• Soffit/Attic Height: > 6-1/2".

Image: Pre-installation considerations for attic and soffit space.

4.2 Installation with Attic Access

1. Starting next to a joist, trace an outline for the fan housing.
2. Use a drywall saw to cut the marked opening.
3. Slide the fan housing into the opening and screw it into the joist.
4. Attach the duct to the fan's exhaust port and apply HVAC tape over the connection to ensure a secure seal.
5. Connect the house wires to the fan wires (black to black, white to white, ground to ground).
6. Place insulation over and around the fan housing.
7. Plug in the light connection.
8. Install the grille, LED bulbs, and glass cover.

4.3 Installation without Attic Access (No-Attic Installation)

1. If attic access is not available, this model allows for no-attic installation.
2. First, disconnect the wires connecting the motor and the housing.
3. Remove the fixing screws on the outside of the housing. This allows you to remove the motor from the housing.
4. After connecting the ventilation duct, send the housing into the ceiling opening.
5. Connect the wires correctly according to the label on the wires (black to black, white to white, ground to ground).
6. Secure the housing to the joist using appropriate fasteners.
7. Reinstall the motor back into the housing and connect the plugs.
8. Finally, install the grille, LED bulbs, and glass cover.

4.4 Diagrama de cableado

Image: Electrical wiring diagram for connecting the fan and light to a switch.

5. Instrucciones de funcionamiento

The Akicon BPT14-80CL fan is designed for efficient and quiet operation.

5.1 Funcionamiento del ventilador

• The fan operates at 80 CFM (Cubic Feet Per Minute) with a noise level of 2.0 Sones, ensuring effective ventilation with minimal sound.
• Activate the fan using the connected wall switch.

5.2 Funcionamiento de la luz LED

• The integrated LED light offers three color temperature options: 3000K (Warm White), 4000K (Cool White), and 5000K (Daylight).
• To select your desired color temperature, locate the sliding switch on the back of the lampshade (or on the LED bulbs themselves, depending on the specific bulb type). Adjust this switch before installing the glass cover.
• The LED light is dimmable, allowing you to adjust brightness using a compatible dimmer switch (sold separately).

Imagen: Más alláview of the fan's performance and lighting features.

6. Mantenimiento

El mantenimiento regular garantiza un rendimiento óptimo y la longevidad de su ventilador de extracción.

6.1 Cleaning the Grille and Glass Cover

• Disconnect power at the service panel before cleaning.
• Carefully remove the glass cover by rotating it counter-clockwise.
• Wash the glass cover with mild soap and water, then dry thoroughly.
• Limpie la rejilla con publicidad.amp Paño. No utilice limpiadores abrasivos.
• Reinstall the glass cover by aligning the markings and rotating clockwise until secure.

6.2 Sustitución de bombillas LED

• Desconecte la energía en el panel de servicio.
• Remove the glass cover as described above.
• Unscrew the old LED bulbs and replace them with new ones of the same type (GU24 base, if applicable, or compatible LED bulbs).
• Reinstall the glass cover.

7. Solución de problemas

Si su ventilador no funciona correctamente, consulte los siguientes problemas comunes:

8. Garantía y soporte

This Akicon Bathroom Exhaust Fan comes with a 3-Year Limited Warranty, ensuring confidence in the quality and construction of the product.

8.1 Atención al cliente

For questions, problems, or missing parts, please contact Akicon Customer Service:

• Horario de servicio: De 8 a. m. a 6 p. m. EST, de lunes a viernes
• Teléfono: +1 (302) 213-4406
• Correo electrónico: servicio@akiconshop.com