Introducción
Thank you for choosing the Jambo 16-inch Liquid Motion Lamp. This manual provides essential information for the safe and proper use, setup, operation, and maintenance of your lampLéalo detenidamente antes de usarlo y consérvelo para futuras consultas.
The Jambo Liquid Motion Lamp creates a mesmerizing visual display as heated wax slowly rises and falls within a liquid-filled glass vessel. This dynamic effect provides a calming and decorative ambiance for any indoor space.
Información de seguridad
Para garantizar un funcionamiento seguro y evitar daños, tenga en cuenta las siguientes precauciones de seguridad:
- Uso exclusivo en interiores: Este lamp is designed for indoor use in dry locations. Do not use it outdoors or in wet environments.
- Seguridad eléctrica: Asegúrese de que lamp is connected to a 120-volt power outlet. Do not overload electrical outlets.
- Advertencia de calor: El lamp and its contents become hot during operation. Do not touch the glass or base while the lamp is on or immediately after turning it off. Allow sufficient time for cooling.
- Colocación estable: Coloque la lamp on a flat, stable, and heat-resistant surface away from edges where it could be easily knocked over.
- Avoid Shaking: Do not shake, drop, or move the lamp while it is operating or hot, as this can damage the internal components and cause the liquid to become cloudy.
- Mantener alejado de niños y mascotas: Due to the heat generated, keep the lamp fuera del alcance de los niños y las mascotas.
- Ventilación: Asegúrese de que haya una circulación de aire adecuada alrededor del lamp to prevent overheating. Do not cover the lamp.
- Cable dañado: Si el cable de alimentación está dañado, debe ser reemplazado por el fabricante o un agente de servicio calificado para evitar peligros.
Contenido del paquete
Verifique que todos los componentes estén presentes al desembalar:
- 1 x Jambo Liquid Motion Lamp Unit (Base, Glass Vessel, Cap)
- 1 x 30-Watt Incandescent Bulb (E17 base)
Configuración
Follow these steps to set up your Jambo Liquid Motion Lamp:
- Deshacer: Retire con cuidado todos los componentes del embalaje.
- Instalación de la bombilla: If the bulb is not pre-installed, gently screw the included 30-watt E17 incandescent bulb into the socket located in the lamp base. Do not overtighten.
- Place Glass Vessel: Carefully place the glass vessel onto the lamp base, ensuring it sits securely.
- Attach Cap: Place the decorative cap onto the top of the glass vessel.
- Posición Lamp: Coloque el l ensambladoamp on a flat, stable, and heat-resistant surface, away from direct sunlight, extreme temperatures, or drafts.
- Conecte la electricidad: Conecte el cable de alimentación a una toma eléctrica estándar de 120 voltios.
Instrucciones de funcionamiento
Operating your Jambo Liquid Motion Lamp es sencillo:
- Encender: Locate the rotary switch on the power cord or base (depending on model) and turn it to the 'ON' position. The bulb will illuminate.
- Tiempo de calentamiento: For the first use, or after extended periods of inactivity, the lamp may take 2-4 hours to fully warm up and for the wax to begin flowing smoothly. This is normal.
- Wax Movement: Once warmed, the wax will begin to soften, rise, and fall in captivating patterns. The lamp operates best at room temperature (20-25°C / 68-77°F).
- Duración de funcionamiento: For optimal performance and longevity, it is recommended to operate the lamp for no more than 8-10 hours at a time. Allow it to cool down completely before restarting.
- Apagar: Para apagar el lamp, rotate the switch to the 'OFF' position and unplug it from the power outlet when not in use for extended periods.
Mantenimiento
El cuidado adecuado garantizará la longevidad y el rendimiento de su lamp:
- Limpieza: Asegúrese de que lamp is unplugged and completely cool before cleaning. Wipe the exterior of the glass and base with a soft, damp cloth. Do not use abrasive cleaners or immerse any part of the lamp en el agua.
- Reemplazo de bombilla: If the bulb burns out, unplug the lamp and allow it to cool. Carefully remove the old bulb and replace it with a new 30-watt, E17 base incandescent bulb. Ensure the replacement bulb matches the original specifications.
- Almacenamiento: Si almacena el lamp for an extended period, ensure it is clean, dry, and stored upright in a cool, dark place.
- No abrir: Never attempt to open the sealed glass vessel or tamper with its contents. This will void any warranty and can be dangerous.
Solución de problemas
If you encounter issues with your Jambo Liquid Motion Lamp, consulte los siguientes problemas y soluciones comunes:
| Problema | Posible causa | Solución |
|---|---|---|
| Lamp no se enciende. | No power, faulty bulb, or loose connection. | Comprueba si el lamp is properly plugged in. Ensure the power outlet is functional. Verify the rotary switch is in the 'ON' position. Replace the bulb if it is burnt out. |
| Wax is not moving or moving slowly. | Insufficient warm-up time, cold room temperature, or incorrect bulb wattage. | Allow 2-4 hours for the lamp to fully warm up. Ensure the room temperature is between 20-25°C (68-77°F). Confirm the bulb is a 30-watt E17 incandescent type. |
| Liquid is cloudy. | Initial cloudiness, lamp shaken, or improper storage. | Initial cloudiness often clears after several hours of continuous operation. Avoid shaking or dropping the lamp. If cloudiness persists after multiple uses, contact customer support. |
| Wax is stuck at the top or bottom. | Not fully warmed up, lamp tilted, or excessive heat/cold. | Asegúrese de que lamp has had sufficient warm-up time. Verify the lamp is placed on a level surface. Avoid placing the lamp near heat sources or in very cold areas. |
Presupuesto
Key technical specifications for the Jambo 16-inch Liquid Motion Lamp (Model KL-217):
| Característica | Detalle |
|---|---|
| Número de modelo | KL-217 |
| Dimensiones (D x W x H) | 11.4 cm x 11.4 cm x 39.4 cm (aprox. 4.5 x 4.5 x 15.5 pulgadas) |
| Altura de la sombra | 16 pulgadas |
| Fuente de poder | Eléctrico con cable |
| Volumentage | 120 voltios |
| Quétage | 30 vatios |
| Tipo de bombilla | Incandescente |
| Base de la bombilla | E17 |
| Tipo de interruptor | Giratorio |
| Material base | Aluminio |
| Material de la sombra | Vaso |
| Tipo de acabado | Metálico |
| Uso interior/exterior | Interior |
| Nivel de resistencia al agua | No es impermeable |
| Código Postal | 850019692297 |
Garantía y soporte
Jambo is committed to providing high-quality products. While specific warranty details are not provided in this manual, please retain your proof of purchase for any warranty claims.
For technical support, troubleshooting assistance beyond what is covered in this manual, or inquiries regarding parts and service, please contact Jambo customer support through the retailer where you purchased the product or visit the official Jambo websitio para información de contacto.