TYAN MiTAC Thunder CX GC68A-B7126 Cloud Server User Manual

1. Introducción

This manual provides essential information for the safe and efficient operation of your TYAN MiTAC Thunder CX GC68A-B7126 B7126G68AV10E2HR -1U2S Cloud Server. It covers installation, configuration, maintenance, and troubleshooting procedures. Please read this manual thoroughly before installing or operating the server.

2. Información de seguridad

Tenga en cuenta las siguientes precauciones de seguridad para evitar lesiones y daños al equipo:

• Desconecte siempre la alimentación antes de realizar cualquier procedimiento de mantenimiento o instalación.
• Asegure una conexión a tierra adecuada para evitar descargas eléctricas.
• Handle components with care to avoid electrostatic discharge (ESD) damage. Use an anti-static wrist strap.
• Do not operate the server in environments with excessive heat, humidity, or dust.
• Ensure adequate ventilation around the server to prevent overheating.

3. Contenido del paquete

Verify that all items are present and undamaged. If any items are missing or damaged, contact your vendor immediately.

• TYAN MiTAC Thunder CX GC68A-B7126 Server Unit
• Cables de alimentación (la cantidad puede variar según la región)
• Rackmount Rail Kit
• Documentation (Quick Start Guide, CD/USB with drivers and utilities)
• Accessory Kit (screws, cables, etc.)

4. Exceso de físicoview

Esta sección proporciona una descripción generalview of the server's external and internal components.

4.1 Delantero y Trasero View

Figure 4.1: Combined front and rear view of the server, showing hot-swap drive bays on the front and I/O ports and redundant power supplies on the rear.

4.2 Panel frontal

Figure 4.2: Close-up of the server's front panel, featuring 12 hot-swap 2.5-inch drive bays, USB ports, and system status LEDs.

4.3 Disposición interna

Figura 4.3: Interna view of the server, showcasing the motherboard with DIMM slots, CPU sockets, PCIe slots, and cooling fan modules.

5. Configuración

5.1 Instalación en bastidor

The server is designed for installation in a standard 19-inch rack. Follow the instructions provided with the rackmount rail kit to securely mount the server.

5.2 Instalación de componentes

Before installing components, ensure the server is powered off and disconnected from the power source.

5.2.1 Memory (DIMMs) Installation

1. Open the server chassis cover.
2. Localice las ranuras DIMM en la placa base.
3. Open the retaining clips at both ends of the DIMM slot.
4. Align the memory module with the slot key and press firmly until the clips snap into place.
5. Ensure all DIMMs are seated correctly.

5.2.2 Instalación de la unidad de almacenamiento

The server supports 2.5-inch hot-swap SATA and NVMe drives.

1. For hot-swap drives, ensure the drive tray is empty.
2. Mount the 2.5-inch drive into the drive tray using the provided screws.
3. Slide the drive tray into an available hot-swap bay until it clicks into place.
4. For M.2 NVMe drives, open the chassis and locate the M.2 slot on the motherboard. Install the M.2 drive and secure it with the screw.

Instalación de la tarjeta PCIe 5.2.3

The server features 2 x FH/HL PCIe Gen4 x16 slots.

1. Open the server chassis cover.
2. Remove the blanking plate from the desired PCIe slot.
3. Carefully insert the PCIe card into the slot, ensuring it is fully seated.
4. Secure the card with the retaining mechanism or screw.

5.3 Cableado

• Cables de alimentación: Connect the redundant power supplies to separate power sources for redundancy.
• Cables de red: Connect the GbE ports to your network infrastructure. Connect the dedicated IPMI port for remote management.
• Peripheral Cables: Connect any necessary USB devices, keyboard, mouse, or VGA monitor.

5.4 Encendido inicial

After all components are installed and cables connected, press the power button on the front panel. Observe the system LEDs for normal operation. The server should initiate the boot process.

6. Operación del servidor

6.1 Configuración del BIOS/UEFI

To access the BIOS/UEFI setup utility, press the designated key (usually DEL or F2) during the Power-On Self-Test (POST) sequence. Here you can configure boot order, system time, and other hardware settings.

6.2 Instalación del sistema operativo

Insert your operating system installation media (USB drive or network boot) and configure the boot order in BIOS/UEFI to start from the installation media. Follow the on-screen instructions to install your preferred operating system.

6.3 IPMI Management

The Intelligent Platform Management Interface (IPMI) allows for remote monitoring and management of the server, even when the main operating system is not running. Connect the dedicated IPMI LAN port to your network. Access the IPMI web interfaz a través de un web browser using the assigned IP address. Refer to the IPMI user guide for detailed instructions.

7. Mantenimiento

El mantenimiento regular garantiza un rendimiento óptimo y la longevidad de su servidor.

7.1 actualizaciones de firmware

Revise periódicamente las instrucciones del fabricante. website for updated BIOS, BMC, and other component firmware. Keeping firmware up-to-date can improve stability, performance, and security. Follow the provided instructions carefully during the update process.

7.2 Reemplazo de componentes

• Hot-Swap Drives: Drives can be replaced without powering down the server. Ensure the replacement drive is compatible and follow the operating system's procedures for drive replacement in a RAID configuration.
• Redundant Power Supplies: The server features hot-swappable redundant power supplies. If one PSU fails, it can be replaced while the server remains operational. Disconnect the failed PSU, remove it, and insert the new one.

7.3 Limpieza

Dust accumulation can impede airflow and cause overheating. Periodically clean the server's interior using compressed air. Ensure the server is powered off and disconnected from power before cleaning. Do not use liquid cleaners directly on components.

8. Solución de problemas

Esta sección proporciona soluciones a problemas comunes que puede encontrar.

8.1 Problemas comunes y soluciones

• Sin energía: Check power cable connections, power supply status LEDs, and ensure power outlets are functional.
• Error de arranque: Verify boot order in BIOS/UEFI, check for loose memory modules or expansion cards, and ensure storage drives are detected.
• Problemas de conectividad de red: Check network cable connections, network adapter status LEDs, and network configuration in the operating system.
• Calentamiento excesivo: Ensure proper ventilation, clean dust from fans and heatsinks, and check ambient temperature.

8.2 Indicadores LED

Refer to the server's front panel and internal LEDs for diagnostic information. Different LED patterns or colors indicate specific system statuses or errors. Consult the detailed hardware manual for a complete list of LED codes.

9. Especificaciones

10. Garantía y soporte

This TYAN server comes with a standard manufacturer's warranty. For detailed warranty terms and conditions, please refer to the warranty card included with your product or visit the official Tyan website. For technical support, driver downloads, and further assistance, please contact Tyan customer service or your authorized reseller.