1. Producto terminadoview
The Lutron Diva DVSCELV-300P-BI is a 300-watt single pole electronic low-voltage dimmer designed to control lighting from one location. It features a large paddle switch for on/off control and a linear slider for precise dimming adjustments. This dimmer is specifically for use with electronic low-voltage lighting applications. It allows users to adjust light levels, contributing to energy savings and creating desired room atmospheres. Wallplates are sold separately.
2. Información de seguridad
- ADVERTENCIA: PELIGRO DE DESCARGA ELÉCTRICA. May result in serious injury or death. Turn OFF power at the circuit breaker or fuse box before installing.
- Instale de acuerdo con todos los códigos eléctricos nacionales y locales.
- Si no está seguro de alguna parte de estas instrucciones, consulte a un electricista calificado.
- Do not use with standard incandescent, magnetic low-voltage, or fluorescent lighting. This dimmer is for electronic low-voltage solo aplicaciones.
- Asegurar el agua total.tage of the connected lighting does not exceed 300 watts.
3. Contenido del paquete
- Lutron Diva DVSCELV-300P-BI Dimmer
- Wire connectors (various colors, typically yellow and blue)
- Guía de instalación
Note: Wallplate is not included and must be purchased separately.
4. Especificaciones
| Característica | Detalle |
|---|---|
| Número de modelo | DVSCELV-300P-BI |
| Quétage | 300 vatios |
| Vol de funcionamientotage | 120 voltios |
| Tipo de circuito | Single Pole (1-way) |
| Solicitud | Electrónica de bajo volumentage (VPE) |
| Dimensiones (L x An x Al) | 1.75 x 2.2 x 4.25 pulgadas |
| Color | Galleta |
| Método de control | Paddle Switch with Linear Slider |
| Material | Cobre (material de contacto) |
5. Instalación
Before beginning installation, ensure you have turned off power at the circuit breaker. This dimmer is designed for single-pole applications where the light is controlled from one switch. A neutral wire connection is typically required for proper operation.
5.1. Preparación
- Apague la energía: Ubique el panel de disyuntores y apague el interruptor de luz que está reemplazando.
- Verifique que la energía esté apagada: Flip the existing switch on and off to confirm the power is disconnected.
- Remove existing wallplate and switch: Unscrew the wallplate and then the mounting screws holding the old switch in place. Carefully pull the switch out from the wall box.
- Identificar los cables: Note the connections of the existing wires. Typically, a single-pole switch will have two load/line wires and a ground wire. Some dimmers may require a neutral wire (usually white).
Imagen: Frente view of the Lutron Diva DVSCELV-300P-BI Electronic Low-Voltage Dimmer, showing the paddle switch and linear slider.
Imagen: Lateral view of the Lutron Diva DVSCELV-300P-BI Dimmer, illustrating the pre-stripped wires for connection.
5.2. Wiring the Dimmer
The Lutron Diva DVSCELV-300P-BI dimmer typically has three wires: a green wire (ground), a black wire (hot/line), and a yellow wire (load). Some models may also include a white wire (neutral).
- Cable a tierra: Connect the green wire from the dimmer to the bare copper or green ground wire in the wall box using a wire connector.
- Cable caliente/de línea: Connect the black wire from the dimmer to the incoming hot/line wire from the circuit breaker (often black or red) using a wire connector.
- Cable de carga: Connect the yellow wire from the dimmer to the load wire that goes to the light fixture (often black or red) using a wire connector.
- Neutral Wire (if applicable): If your dimmer has a white wire and your wall box has a neutral wire bundle (usually white wires twisted together), connect the white dimmer wire to the neutral bundle using a wire connector. If no neutral wire is present in the wall box, cap off the white wire from the dimmer with a wire connector.
Video: This video demonstrates the wiring process for a single-pole dimmer with one black, one yellow, and one white wire, which is applicable to the Lutron Diva DVSCELV-300P-BI. It covers connecting the ground, hot, load, and neutral wires.
5.3. Finishing Installation
- Secure the dimmer: Carefully push all wires back into the wall box. Mount the dimmer to the wall box using the provided screws.
- Attach wallplate: Install the coordinating wallplate (sold separately) over the dimmer.
- Restaurar energía: Return to your circuit breaker panel and turn the power back on.
Image: The Lutron Diva DVSCELV-300P-BI Dimmer installed in a wall, ready for use.
6. Operación
- Encender y apagar las luces: Press the large paddle switch to turn the connected lights on or off.
- Ajuste del brillo: Use the linear slider located next to the paddle switch to adjust the light level. Slide up for brighter lights and down for dimmer lights.
- Atenuación preestablecida: The dimmer will return to the previously set light level when turned back on.
Image: A hand demonstrating the operation of the Lutron Diva DVSCELV-300P-BI Dimmer, highlighting the paddle switch and linear slider.
7. Mantenimiento
- Limpieza: Clean the dimmer and wallplate with a soft, damp Paño. No utilice limpiadores abrasivos ni disolventes.
- No hay piezas que el usuario pueda reparar: El regulador no contiene piezas que el usuario pueda reparar. No intente abrir ni reparar la unidad.
8. Solución de problemas
| Problema | Posible causa / solución |
|---|---|
| Las luces no se encienden. |
|
| Lights flicker or buzz. |
|
| El regulador de intensidad no atenúa la luz correctamente. |
|
9. Garantía y soporte
For warranty information, technical support, or further assistance, please visit the official Lutron website or contact Lutron customer service. Keep your purchase receipt for warranty claims.
Lutron Support: Lutron.com/soporte
