Introducción
The Intermatic PE153P is a versatile 3-circuit digital timer designed for automatic control of electrical loads. This 24-hour control mechanism allows for precise scheduling of various applications, including lighting, heating, air conditioning, and pool or spa pumps. Each circuit can manage loads up to 17 amps. This manual provides essential information for the safe installation, programming, operation, and maintenance of your PE153P digital timer.
Figura 1: Intermatic PE153P 3-Circuit Digital Timer. This image shows the timer unit with its rainproof enclosure open, revealing the digital display, control buttons, and wiring terminals. The enclosure is designed to protect the internal components from environmental elements.
Información de seguridad
Observe siempre las siguientes precauciones de seguridad para reducir el riesgo de incendio, descarga eléctrica o lesiones:
- Installation must be performed by a qualified electrician and in accordance with all national and local electrical codes.
- Disconnect power at the circuit breaker or fuse box before installing or servicing the timer.
- Ensure the timer is properly grounded.
- Do not exceed the maximum load ratings for each circuit (17 amps).
- This device is intended for outdoor use and is housed in a rainproof enclosure. Ensure the enclosure is securely closed after installation and servicing.
Instalación y configuración
Montaje de la carcasa
- Select a suitable location for mounting the timer. The location should be easily accessible for programming and maintenance, and protected from direct sunlight if possible to prolong LCD life.
- Use appropriate mounting hardware (not included) to secure the enclosure to a flat, vertical surface. Ensure the enclosure is level.
Instrucciones de cableado
ADVERTENCIA: Disconnect power at the main service panel before wiring. Failure to do so may result in serious injury or death.
- Open the timer enclosure.
- Identify the input terminals (LINE 1, LINE 2, NEUTRAL) and output terminals for each of the three circuits (LOAD 1, LOAD 2, LOAD 3).
- Connect the incoming power supply wires to the appropriate input terminals. For 120V operation, connect LINE 1 and NEUTRAL. For 240V operation, connect LINE 1 and LINE 2.
- Connect the load wires for each device you wish to control to the corresponding output terminals.
- Ensure all wire connections are tight and secure. Use copper conductors only, rated for at least 75°C.
- Cierre y asegure la puerta del gabinete.
Instrucciones de funcionamiento
Initial Power-Up and Time Setting
- Restore power to the timer at the main service panel.
- The LCD display will illuminate. If the display is blank, check power connections.
- Presione el PROGRAMA para ingresar al modo de programación.
- Utilice el UP y ABAJO arrows to set the current time (hour and minute).
- Prensa INGRESAR para confirmar cada ajuste.
- Set the current day of the week using the UP y ABAJO arrows, then press INGRESAR.
Horarios de programación
The PE153P offers seven preprogrammed modes and custom programming. Refer to the detailed programming section in the full manual for advanced settings.
- Prensa PROGRAMA repeatedly to cycle through the available circuits (CIRCUIT 1, CIRCUIT 2, CIRCUIT 3).
- Once the desired circuit is selected, press INGRESAR to begin setting ON/OFF times.
- Usar UP y ABAJO arrows to set the ON time, then press INGRESAR.
- Repeat for the OFF time.
- Seleccione los días de la semana en que este horario estará activo.
- Prensa PROGRAMA to save and exit, or to move to the next program event.
Anulación manual
To manually turn a circuit ON or OFF outside of its programmed schedule, press the corresponding ANULACIÓN button for that circuit. The override will remain active until the next programmed event or until manually cancelled.
Mantenimiento
The Intermatic PE153P digital timer requires minimal maintenance. Periodically inspect the enclosure for any signs of damage or wear. Ensure the door seal is intact to maintain its rainproof rating. Keep the display and buttons clean and free of debris. No user-serviceable parts are inside the sealed unit beyond the wiring terminals.
Solución de problemas
| Problema | Posible causa | Solución |
|---|---|---|
| La pantalla está en blanco. | No llega energía a la unidad. | Revise el disyuntor/fusible. Verifique las conexiones del cableado. |
| La carga no se enciende ni se apaga según lo programado. | Incorrect programming; Manual override active; Faulty wiring; Load exceeding capacity. | Review programming schedule. Check for active manual override. Inspect wiring. Ensure load is within 17A per circuit. |
| La hora es incorrecta | Time not set correctly; Power interruption. | Reset current time and day. The internal battery should maintain time during short power outages. |
If troubleshooting steps do not resolve the issue, contact Intermatic customer support.
Presupuesto
| Modelo | PE153P |
| Marca | Intermático |
| Vol de entradatage | 120/240 VCA, 60 Hz |
| Numero de circuitos | 3 independent circuits |
| Carga máxima por circuito | 17 Amps (resistive/inductive), 1000W tungsten, 3 HP |
| Tipo de recinto | Rainproof (Type 3R) |
| Características principales | LCD Readout, Multivoltage Input/Output, Countdown, Override, Freeze Protection, Heater Protection |
| Peso del artículo | 2.55 libras |
Garantía y soporte
Información de garantía
Intermatic products are designed for reliability and performance. For specific warranty details, please refer to the warranty card included with your product or visit the official Intermatic webSitio. Conserve su comprobante de compra para reclamaciones de garantía.
Atención al cliente
For technical assistance, programming questions, or to report a problem, please contact Intermatic customer support. Visit the Tienda Intermatic en Amazon o su funcionario webSitio para obtener información de contacto y recursos adicionales.
