Introducción
Welcome to the user manual for the Novak Club Sensored Brushless ESC. This Electric Speed Controller is designed for high-performance remote-controlled vehicles, offering precise control and efficient power delivery for sensored brushless motor systems. This manual provides essential information for the proper setup, operation, maintenance, and troubleshooting of your ESC.
Precauciones de seguridad
To ensure safe operation and prevent damage to your equipment or injury, please observe the following safety guidelines:
- Always disconnect the battery from the ESC when not in use to prevent accidental operation and discharge.
- Asegúrese de que haya una ventilación adecuada alrededor del ESC durante el funcionamiento para evitar el sobrecalentamiento.
- No exponga el ESC al agua ni a la humedad a menos que esté específicamente clasificado como resistente al agua.
- Verify correct polarity when connecting the battery to avoid damage to the ESC and battery.
- Keep fingers and loose clothing away from rotating parts of the motor and vehicle during operation.
- Read and understand all instructions before operating the ESC.
Guía de configuración
Follow these steps to properly connect your Novak Club Sensored Brushless ESC to your RC vehicle's components:
- Conexión del motor: Connect the three motor wires from your sensored brushless motor to the corresponding output terminals on the ESC. Ensure the phase wires (A, B, C) are connected correctly. For sensored motors, connect the sensor wire from the motor to the sensor port on the ESC.
- Conexión de la batería: Connect your battery pack to the battery input wires of the ESC. Pay close attention to polarity: red wire to positive (+), black wire to negative (-). Incorrect polarity will damage the ESC.
- Conexión del receptor: Plug the ESC's receiver cable into the throttle channel (usually Channel 2) of your RC receiver.
- Interruptor de alimentación: Ensure the ESC's power switch is in the OFF position before connecting the battery.
Image: The Novak Club Sensored Brushless ESC, showing its compact design, prominent heat sink for thermal management, and various connection points for motor, battery, and receiver. The clear casing reveals internal components, and the "NOVAK" branding is visible on the side.
Instrucciones de funcionamiento
Calibración inicial
Before first use, it is crucial to calibrate the ESC to your radio system's throttle range. Refer to your radio system's manual for specific calibration procedures, as these can vary. Generally, the process involves:
- Encienda su transmisor de radio.
- Hold the throttle trigger at full brake/reverse.
- Encienda el ESC.
- Wait for the ESC to emit a series of beeps or flashes, indicating it has detected the full brake position.
- Move the throttle trigger to full throttle.
- Espere la confirmación.
- Return the throttle trigger to the neutral position.
- Wait for final confirmation. The ESC is now calibrated.
Funcionamiento normal
Once calibrated, the ESC is ready for use:
- Turn on your radio transmitter first, then connect the battery to the ESC and turn on the ESC.
- The ESC will initialize, and you should hear a series of tones indicating it is ready.
- Control the vehicle using your radio transmitter's throttle and steering.
- When finished, turn off the ESC first, then turn off your radio transmitter, and finally disconnect the battery.
Mantenimiento
Regular maintenance helps ensure the longevity and optimal performance of your ESC:
- Limpieza: Regularly clean the ESC, especially the heat sink, to remove dirt, dust, and debris. Use a soft brush or compressed air. Do not use solvents or harsh chemicals.
- Inspección: Inspeccione periódicamente todos los cables y conectores para detectar signos de desgaste, desgaste o corrosión. Asegúrese de que todas las conexiones estén bien sujetas.
- Almacenamiento: Guarde el ESC en un lugar seco y fresco, alejado de la luz solar directa y de temperaturas extremas.
Solución de problemas
If you encounter issues with your ESC, refer to the table below for common problems and their solutions:
| Problema | Posible causa | Solución |
|---|---|---|
| ESC does not power on | Battery not connected, Battery discharged, Power switch off | Check battery connection, Charge battery, Turn on power switch |
| El motor no gira | Motor wires loose, Sensor wire disconnected, ESC not calibrated, Radio interference | Check motor connections, Reconnect sensor wire, Perform ESC calibration, Check radio system |
| ESC se sobrecalienta | Insufficient ventilation, Motor/gear ratio too high, ESC overloaded | Ensure proper airflow, Adjust gear ratio, Use appropriate motor for ESC rating |
| Control errático | Radio interference, Loose receiver connection, Low battery voltage | Check radio system, Secure receiver cable, Charge battery |
Presupuesto
Key specifications for the Novak Club Sensored Brushless ESC:
- Modelo: 3930-2S
- Material: Plástico, metal
- Dimensiones (L x An x Al): 5.2 x 3.8 x 1.8 pulgadas
- Peso: Approximately 5 ounces (4.96 ounces)
- Fabricante: NOVAK
- Tipo: Sensored Brushless Electric Speed Controller
Garantía y soporte
For warranty information or technical support regarding your Novak Club Sensored Brushless ESC, please contact Integy customer service or visit their official webSitio. Conserve su comprobante de compra para cualquier reclamación de garantía.
Nota: Los términos y condiciones específicos de la garantía pueden variar y están sujetos a la política del fabricante en el momento de la compra.
