KFI Products 105170 Replacement Plow Blade Skid Kit User Manual

1. Introducción

This manual provides instructions for the proper installation, operation, and maintenance of the KFI Products 105170 Replacement Plow Blade Skid Kit. This kit is designed to replace worn or damaged skids on compatible snow plow blades, helping to protect the plow's cutting edge and optimize its performance on various surfaces. Please read this manual thoroughly before installation and use to ensure safe and effective operation.

2. Información de seguridad

Always observe safety precautions when working with heavy equipment and tools. Failure to follow these instructions may result in injury or damage to equipment.

• Use equipo de protección personal (EPP) adecuado, incluidas gafas de seguridad y guantes.
• Ensure the plow blade is securely supported and stable before beginning any installation or maintenance.
• Keep hands and clothing clear of pinch points and moving parts.
• Use only KFI Products approved replacement parts.
• Do not modify the skid kit or plow blade in any way that deviates from the manufacturer's design.

3. Contenido del paquete

Verifique que todos los componentes estén presentes antes de continuar con la instalación:

• Plow Skid Assemblies (Quantity: 2, typically)
• Mounting Hardware (Bolts, Washers, Nuts, Cotter Pins)
• Instruction Sheet (This manual)

Note: Specific hardware quantities may vary. Refer to the parts diagram if available with your kit.

4. Configuración e instalación

This section details the steps for installing the replacement plow blade skid kit.

4.1 Herramientas necesarias

• Wrench set (appropriate sizes for mounting hardware)
• Socket set (optional, for faster installation)
• Gafas de seguridad
• Guantes

4.2 pasos de instalación

1. Prepare the Plow Blade: Position the snow plow blade on a flat, stable surface. Ensure it is disengaged from the vehicle and cannot move unexpectedly. If replacing old skids, remove them by unbolting the existing hardware.
2. Position the Skid Assembly: Place one skid assembly against the back of the plow blade, aligning the mounting holes on the skid bracket with the pre-drilled holes on the plow blade. The skid shoe should be positioned towards the bottom edge of the blade.
3. Secure the Skid: Insert the provided bolts through the skid bracket and plow blade holes. Secure them with washers and nuts on the opposite side. Hand-tighten initially.
4. Repeat for Second Skid: Install the second skid assembly on the opposite side of the plow blade, following steps 2 and 3.
5. Adjust Skid Height: The skid height is adjustable to control the distance the plow blade's cutting edge is off the ground. This is typically done by adding or removing washers above or below the skid shoe's mounting plate, or by adjusting a threaded shaft if applicable. Adjust both skids to the desired height, ensuring they are level.
6. Ajuste final: Once the skids are at the desired height and level, fully tighten all mounting hardware using appropriate wrenches. Ensure all bolts are snug to prevent loosening during operation.
7. Verificar instalación: Double-check all connections for tightness and ensure the skids are securely mounted and properly adjusted.

Figura 1: De cerca view of the KFI Products 105170 Replacement Plow Blade Skid Kit installed on a snow plow blade. This image illustrates the skid assembly, including the mounting bracket, main shaft, adjustment washers, rubber bumper, and the circular skid shoe, all securely bolted to the plow blade.

5. Instrucciones de funcionamiento

The plow skids are designed to elevate the plow blade's cutting edge slightly above the ground surface, preventing it from digging into gravel, grass, or uneven terrain. Proper adjustment is key to effective operation.

• Adjusting for Surface Type:
  • For gravel or uneven surfaces, adjust the skids to lift the cutting edge higher, typically 1-2 inches off the ground, to prevent scraping and damage.
  • For paved surfaces, the skids can be adjusted lower, allowing the cutting edge to be closer to the ground for more efficient snow removal, while still providing protection against direct contact.
• Presión uniforme: Ensure both skids are adjusted to the same height to maintain even pressure on the plow blade and prevent uneven wear.
• Inspección regular: Periodically check the skid height during plowing operations, especially after encountering obstacles or rough terrain.

6. Mantenimiento

Regular maintenance will extend the life of your KFI Products 105170 Skid Kit.

• Inspeccionar por desgaste: Before each plowing season and periodically during use, inspect the skid shoes for excessive wear. Replace skids when they show significant thinning or damage to maintain proper plow height and protection.
• Comprobar hardware: Ensure all mounting bolts, nuts, and cotter pins are tight and secure. Re-tighten as necessary.
• Limpio: After each use, clean any accumulated snow, ice, or debris from the skid assemblies.
• Almacenamiento: Store the plow and skid kit in a dry environment to prevent rust and corrosion.

7. Solución de problemas

8. Especificaciones

• Número de modelo: 105170
• Marca: Productos KFI
• Peso del artículo: Approximately 5.17 pounds (per skid assembly)
• Dimensiones del producto: Approximately 9 x 4.5 x 4 inches (individual skid assembly)
• Material: Construcción de acero de alta resistencia.
• Compatibilidad: Designed for KFI Products snow plow blades and other compatible plow systems.

9. Garantía y soporte

For warranty information or technical support regarding your KFI Products 105170 Replacement Plow Blade Skid Kit, please refer to the official KFI Products webSitio web o contacte con el departamento de atención al cliente. Conserve su recibo de compra como comprobante.

Información de contacto de productos KFI:

• Websitio: www.kfiproducts.com (Nota: Este es un marcador de posición URL, please verify the actual manufacturer's websitio.)
• Servicio al cliente: Consulte la webSitio para números de contacto o soporte por correo electrónico.