1. Introducción
The GoPro Suction Cup Mount is designed for securely attaching your GoPro camera to vehicles, boats, motorcycles, and other smooth, non-porous surfaces. Engineered for stability and a broad range of motion, this industrial-strength mount has been proven at speeds exceeding 150 mph. It includes a short extension arm for ultra-compact mounting and features both a standard base and a quick release base for convenient transitions between shots and locations.
Important Safety Note: This mount is not recommended for surfing, snowboarding, or other high-impact sports. It is intended for non-impact activities only.
2. ¿Qué hay en la caja?
- Ventosa
- Brazos ajustables
- Base estándar
- Base de liberación rápida
- Bolsa con cordón
3. Configuración e instalación
3.1 Preparación de la superficie
For optimal adhesion and security, ensure the mounting surface is clean, smooth, and dry. Thoroughly clean the area with water and wipe away any dirt, dust, or grease. Leaving the surface slightly damp can sometimes aid in creating a stronger suction seal.
3.2 Colocación de la ventosa
- Place the suction cup firmly against the prepared surface.
- Press down on the center of the suction cup while simultaneously pushing the lever down to create a vacuum seal. Ensure the lever is fully engaged.
- Verify the suction cup is securely attached by gently pulling on it. It should not move or slide.
3.3 Attaching Your GoPro Camera
The mount includes both a standard base and a quick release base. Choose the appropriate base for your needs.
- Base estándar: Align your GoPro camera's mounting fingers with the slots on the standard base. Insert the thumb screw through the fingers and the base, then tighten securely.
- Base de liberación rápida: Slide your GoPro camera's mounting fingers into the quick release buckle until it clicks into place. To remove, press the release tabs on the side of the buckle and slide the camera out.
3.4 Ajuste del ángulo de la cámara
The adjustable arms and ball joint mechanism allow for a broad range of motion and precise camera positioning. Loosen the thumb screws on the adjustable arms to change the angle, then tighten them firmly to lock the position.
Image: GoPro camera attached to the suction cup mount, illustrating the adjustable arm and ball joint for flexible positioning.
3.5 Safety Recommendation
Always use a camera tether when mounting your GoPro to a moving vehicle or during any activity where the camera could potentially detach. This provides an extra layer of security for your equipment.
4. Operación del soporte
The quick release base facilitates rapid changes in camera position or location. Simply press the release tabs on the side of the buckle to detach the camera, and then re-attach it to another compatible mount or re-position it as needed. This allows for efficient capture of diverse perspectives without extensive re-setup.
5. Mantenimiento
- Limpieza: Regularly clean the suction cup and mounting surface to ensure optimal adhesion. Use water and a soft cloth to remove any residue.
- Almacenamiento: Store the suction cup mount in a clean, dry place away from direct sunlight when not in use. Avoid storing it with the suction cup pressed against a surface for extended periods, as this can deform the rubber.
6. Solución de problemas
6.1 Pérdida de succión
If the suction cup is not holding securely or loses suction:
- Ensure both the suction cup and the mounting surface are perfectly clean and free of any debris, dust, or oils.
- Apply the suction cup to a smooth, non-porous surface. Textured or porous surfaces will prevent a proper seal.
- Firmly press the center of the suction cup while engaging the lever. Sometimes, a slight dampness on the suction cup can improve the seal.
- Check for any damage or deformities on the rubber suction cup. A damaged cup may not be able to form a reliable seal.
7. Especificaciones
| Característica | Detalle |
|---|---|
| Dimensiones del producto | 6 x 1.7 x 9 pulgadas |
| Peso del artículo | 2.08 onzas |
| Número de modelo | AUCMT-302 |
| Color | Negro |
| Tipo de montaje | Ventosa |
| Dispositivos compatibles | GoPro Cameras (Hero 10, Hero 9, Hero 8, Max) |
Image: Compatibility of the GoPro Suction Cup Mount with various GoPro camera models.
8. Garantía y soporte
8.1 Aviso Legal
SIN GARANTÍA EXPRESA. SIN REEMBOLSO/DEVOLUCIÓN SI SE ABRE EL EMBALAJE DE VENTA AL POR MENOR.
8.2 Atención al cliente
For further assistance or inquiries, please visit the official GoPro support websitio o póngase en contacto con su servicio de atención al cliente.
9. Product in Action
Video: GoPro camera in action, demonstrating its use in various scenarios. This video is provided by Amazon Camera (Seller).
