Introducción
This manual provides essential instructions for the installation, operation, and maintenance of your Texas Instruments 3.7L1200SP rechargeable battery. This battery is designed for compatibility with specific Texas Instruments calculators, including the TI Nspire, TI Nspire CAS, TI Nspire CX, TI Nspire CX CAS (V1.0 with wire), and TI 84 Plus C SE (with wire).
Please read this manual thoroughly before installing and using the battery to ensure proper function and longevity.
Configuración e instalación
Follow these steps to replace or install the rechargeable battery in your compatible Texas Instruments calculator.
- Apagado: Ensure your calculator is completely powered off before beginning the installation process.
- Localice el compartimento de la batería: Identify the battery compartment on the back of your calculator.
- Quitar los tornillos: Use a small Phillips head screwdriver to remove the two screws securing the battery compartment cover. Carefully set the screws aside to avoid losing them.
- Abrir la tapa: Retire con cuidado la tapa del compartimiento de la batería.
- Disconnect Old Battery (if applicable): If replacing an old battery, carefully unplug its connector from the calculator's circuit board. Do not pull on the wires; grasp the connector itself.
- Insertar batería nueva: Position the new 3.7L1200SP battery into the compartment. Ensure it fits snugly.
- Conectar batería nueva: Carefully plug the new battery's connector into the corresponding port on the calculator's circuit board. Ensure the connection is secure.
- Replace Cover and Screws: Place the battery compartment cover back into position and secure it with the two Phillips head screws. Do not overtighten.
Image: The Texas Instruments 3.7L1200SP rechargeable battery. This image shows the battery unit, which is installed into the calculator's battery compartment.
After installation, it is recommended to fully charge the battery before initial use.
Operación y carga
The 3.7L1200SP battery is designed for rechargeable use. Follow these guidelines for optimal performance.
Carga inicial
Upon first installation or after extended storage, fully charge the battery. A complete charge may take approximately one day (24 hours) to reach 100% capacity, especially if the battery is completely depleted.
Carga regular
Connect your calculator to a power source using the appropriate charging cable (typically a USB cable provided with your calculator). The calculator's display will usually indicate the charging status. It is advisable to charge the battery when the charge level is low to maintain battery health.
Indicación de duración de la batería
Your calculator's operating system will provide an indication of the battery charge level. This typically shows increments such as 0%, 25%, 50%, 75%, and 100%.
Mantenimiento y cuidado
Proper care can extend the life of your rechargeable battery.
- Evite la descarga profunda: Do not allow the battery to completely discharge for prolonged periods. Recharge it when the charge level is low.
- Almacenamiento: If storing the calculator for an extended period, ensure the battery has a partial charge (around 50%) and store it in a cool, dry place. Avoid extreme temperatures.
- Limpieza: Mantenga el compartimento de la batería limpio y libre de polvo o residuos.
- Temperatura: Operate and charge the battery within recommended temperature ranges (typically room temperature) to prevent damage.
Solución de problemas
Si tiene problemas con su batería, considere las siguientes soluciones comunes:
- La batería no se carga:
- Ensure the charging cable is securely connected to both the calculator and the power source.
- Verifique que la fuente de alimentación esté activa.
- Pruebe con un cable de carga o adaptador de corriente diferente.
- Confirm the battery connector inside the calculator is properly seated.
- Duración corta de la batería:
- Ensure the battery has been fully charged. Initial charges can take longer.
- Check for excessive background processes or high screen brightness on your calculator, which can drain the battery faster.
- If the battery is several years old, its capacity may naturally degrade over time.
- Calculator Not Powering On:
- Asegúrese de que la batería esté instalada correctamente y completamente cargada.
- Connect the calculator to a power source and attempt to power it on while connected.
- If the issue persists, it may not be battery-related. Consult your calculator's specific user manual or Texas Instruments support.
Presupuesto
| Número de modelo | 3.7L1200SP |
| Volumentage | 3.7 V |
| Capacidad | 1200 mAh |
| Número de pieza | P11P35-09-N01 (1ICP5/43/50) |
| Tipo de batería | Iones de litio |
| Compatibilidad | TI Nspire, TI Nspire CAS, TI Nspire CX, TI Nspire CX CAS (V1.0 with wire), TI 84 Plus C SE (with wire) |
| Peso del artículo | 1.13 onzas |
| Dimensiones del paquete | 2.68 x 2.68 x 0.59 pulgadas |
Garantía y soporte
For warranty information or technical support regarding your Texas Instruments battery or calculator, please refer to the official Texas Instruments webSitio web o contacte directamente con el servicio de atención al cliente. Conserve su recibo de compra como comprobante.
Oficial de Texas Instruments Websitio: education.ti.com
