Introducción
This manual provides comprehensive instructions for the installation, operation, and maintenance of the Hunter 99179 Original Ceiling Fan Remote Control and Canopy Kit. This kit is specifically designed to enhance the functionality of Hunter "Original" series ceiling fans by adding remote control capabilities for fan speeds and lighting.
The kit includes a remote control unit and a canopy designed to house the receiver. It integrates with your existing two-wire fan setup, offering convenient control over three fan speeds and the fan's light fixture.
Información importante de seguridad
- Seguridad eléctrica: Always disconnect power at the circuit breaker or fuse box before attempting any installation, maintenance, or repair. Failure to do so can result in serious injury or death.
- Compatibilidad: This kit is designed for use SOLO with Hunter "Original" series ceiling fans. It is not compatible with other fan models or brands.
- Downrod Requirement: Installation requires a downrod of 12 inches or longer (sold separately). The receiver unit is designed to fit within the canopy, which necessitates sufficient space provided by a longer downrod.
- Instalación profesional: If you are unfamiliar with electrical wiring or ceiling fan installation, it is recommended to consult a qualified electrician.
- Códigos locales: Ensure all installation procedures comply with local electrical codes and ordinances.
- Integridad del producto: No modifique el producto ni lo utilice para fines distintos a su uso previsto.
Contenido del paquete
Verifique que todos los componentes estén presentes antes de comenzar la instalación:
- Unidad de control remoto
- Receptor remoto
- Canopy (for receiver housing)
- Mounting Hardware (screws, wire nuts, etc. - specific items may vary)
Image: A Hunter ceiling fan, representative of the type of fan compatible with the 99179 remote and canopy kit.
Configuración e instalación
Follow these steps carefully to install your Hunter 99179 Remote Control and Canopy Kit:
- Desconexión de energía: Before starting, turn off the electrical power to your ceiling fan at the main circuit breaker or fuse box.
- Cableado de acceso: Carefully lower the existing canopy from your Hunter Original ceiling fan to expose the wiring connections.
- Remove Old Receiver (if applicable): If an old receiver is present, disconnect its wiring and remove it.
- Instalar nuevo receptor: Connect the new remote receiver's wires to the corresponding fan and household wires. Ensure all connections are secure using wire nuts. The receiver is designed to fit within the new canopy.
- Posición del dosel: Carefully tuck the wired receiver into the new canopy. Ensure no wires are pinched.
- Toldo seguro: Mount the new canopy securely to the fan's mounting bracket. Confirm that the downrod is at least 12 inches long to accommodate the receiver within the canopy.
- Restaurar energía: Once installation is complete and all connections are secure, restore power to the ceiling fan at the circuit breaker.
- Emparejar control remoto: Follow the instructions provided with the remote control unit to pair it with the newly installed receiver. This typically involves pressing a button on the remote within a short time after restoring power.
Nota: The new canopy is designed to accommodate the receiver. Some older Hunter Original fan mounting plates or downrods may not be compatible with the new canopy's dimensions. Verify fit before final installation.
Instrucciones de funcionamiento
Your Hunter 99179 remote control provides convenient operation of your ceiling fan and light:
- Control de velocidad del ventilador: Use the designated buttons on the remote to cycle through three fan speeds (Low, Medium, High) or to turn the fan off.
- Control de luz: Use the light button to turn the fan light on or off. Some remotes may also support dimming functions if your fan and light kit are compatible.
- Reemplazo de batería: If the remote control stops responding, replace the batteries. Refer to the remote's specific instructions for battery type and replacement procedure.
Mantenimiento
To ensure optimal performance and longevity of your Hunter 99179 kit:
- Limpieza: Periodically wipe the remote control and canopy with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Comprobación de la batería: Replace remote control batteries as needed to maintain reliable operation.
- Inspección de cableado: Annually, or if issues arise, ensure all electrical connections within the canopy are secure and free from corrosion. Always disconnect power before inspection.
Solución de problemas
If you encounter issues with your remote control and canopy kit, refer to the following common solutions:
| Problema | Posible causa | Solución |
|---|---|---|
| Remote not responding / Fan or light not working |
|
|
| Canopy does not fit / Receiver cannot be housed |
|
|
| Interferencia de otros dispositivos |
|
|
Presupuesto
- Número de modelo: 99179
- Fabricante: Compañía de fans Hunter
- Dimensiones del producto: Aproximadamente 6 x 6 x 7 pulgadas
- Peso del artículo: Aproximadamente 2.35 libras
- Volumentage: 120 voltios
- Fuente de energía: Eléctrico con cable
- Material: Metal
- Proceso de dar un título: Listado en ETL
- Uso: Ceiling fan remote control and canopy accessory
- Característica especial: Heavy Duty construction
- Dispositivos compatibles: Hunter "Original" series ceiling fans
Información de garantía
No specific warranty description is provided for the Hunter 99179 Remote Control and Canopy Kit in the product details. For warranty inquiries, please contact Hunter Fan Company directly or refer to the documentation included with your original Hunter "Original" ceiling fan.
Atención al cliente
For further assistance, technical support, or to inquire about parts, please visit the official Hunter Fan Company websitio o comuníquese con su departamento de servicio al cliente.
Compañía de fans Hunter Websitio: Visit the Hunter Store on Amazon
