RYOBI ZRP320 ONE+ 18V Cordless 2-inch Brad Nailer Instruction Manual

Información importante de seguridad

Always read and understand all safety warnings and instructions before operating this tool. Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury. Keep this manual for future reference. Wear appropriate personal protective equipment, including eye protection, hearing protection, and gloves, when operating the nailer.

Producto terminadoview

The RYOBI ZRP320 ONE+ 18V Cordless 2-inch Brad Nailer is designed for various fastening applications, including trim work, paneling, and other light-duty woodworking projects. This tool utilizes an 18V Lithium-Ion battery (sold separately) and does not require an air compressor, offering cordless convenience.

Figure 1: RYOBI ZRP320 ONE+ 18V Cordless 2-inch Brad Nailer. This image shows the overall design of the nailer, highlighting its compact and cordless nature.

Configuración

1. Instalación de la batería

The RYOBI ZRP320 operates with an 18V ONE+ Lithium-Ion battery (sold separately). Ensure the battery is fully charged before use.

Align the battery with the battery port on the base of the nailer handle.
Deslice la batería en el puerto hasta que encaje firmemente en su lugar.
Para quitarla, presione los pestillos de liberación de la batería y deslícela hacia afuera.

2. Carga de clavos

This nailer uses 18-gauge brad nails ranging from 5/8 inch to 2 inches in length.

Locate the magazine release latch, typically at the rear of the magazine.
Tire hacia atrás el conjunto empujador hasta que encaje en su lugar.
Insert a strip of brad nails into the magazine with the points facing forward.
Release the pusher assembly to push the nails forward into the firing position.
Ensure the low-nail indicator is visible to monitor nail supply.

Figure 2: Magazine of the RYOBI ZRP320 Brad Nailer. This image illustrates the nail magazine where brad nails are loaded for operation.

3. Ajuste de la profundidad de la perforación

The depth of nail drive can be adjusted to suit different materials and desired finishes.

Localice el dial o la palanca de ajuste de profundidad en la herramienta.
Turn the dial or move the lever to increase or decrease the driving depth. Test on a scrap piece of material to achieve the desired depth.

Instrucciones de funcionamiento

1. Selección del modo de actuación

The ZRP320 features a selectable drive shift for single sequential or contact actuation.

Actuación secuencial simple: For precise nail placement. The trigger must be pulled for each nail.
Actuación por contacto: For faster operation. Hold the trigger and press the contact trip against the workpiece to fire nails.

2. Disparo de la clavadora

Asegúrese de que la batería esté instalada y los clavos cargados.
Seleccione el modo de actuación deseado.
Place the nose of the nailer firmly against the workpiece. The contact trip must be compressed.
Aprieta el gatillo para clavar un clavo.
The integrated LED lights will illuminate the work area when the trigger is pulled.

Figura 3: Lado view of the RYOBI ZRP320 Brad Nailer. This image displays the side of the tool, including the handle, trigger, and depth adjustment area.

Mantenimiento

1. Limpieza General

Retire siempre la batería antes de realizar cualquier mantenimiento.
Keep the tool clean and free of debris, especially around the nosepiece and magazine. Use a dry cloth to wipe down the tool.
No utilice disolventes ni productos químicos agresivos, ya que pueden dañar las piezas de plástico.

2. Dry-Fire Lockout

The dry-fire lockout feature prevents the tool from firing when the magazine is empty, protecting the tool and workpiece. Reload nails when the low-nail indicator shows the magazine is nearly empty.

3. Lubricación

Refer to the official RYOBI service manual for specific lubrication requirements. Generally, cordless nailers require minimal lubrication compared to pneumatic models.

Solución de problemas

Problema	Posible causa	Solución
La clavadora no dispara	Batería no instalada o descargada Magazine empty (dry-fire lockout engaged) Contact trip not fully compressed	Instale la batería cargada Recargar clavos Ensure nosepiece is firmly against workpiece
Clavos no completamente clavados	El ajuste de profundidad es demasiado superficial Carga de batería baja Longitud de clavo incorrecta para el material	Adjust depth setting deeper Recargue o reemplace la batería Use appropriate nail length
La clavadora se atasca con frecuencia	uñas dañadas Tamaño de uña incorrecto Debris in magazine or nosepiece	Utilice uñas nuevas y sin daños. Ensure correct 18-gauge brad nails are used Clear any debris from the tool

Presupuesto

Modelo: ZRP320
Fuente de energía: 18V Battery Powered (RYOBI ONE+ system)
Nail Gauge: 18 Calibre
Rango de longitud de las uñas: 5/8 de pulgada a 2 pulgadas
Peso: Aproximadamente 6.5 libras (solo herramienta)
Características especiales: AirStrike Technology, Selectable Drive Shift (Sequential/Contact), Low-Nail Indicator, LED Work Lights, Dry-Fire Lockout
Componentes incluidos: Belt Clip, P320 18-Volt ONE+ Cordless AirStrike 18-Gauge Brad Nailer (Battery and Charger Sold Separately)

Garantía y soporte

This RYOBI ZRP320 ONE+ 18V Cordless 2-inch Brad Nailer comes with a Garantía limitada de 90 días. For warranty claims, technical support, or service inquiries, please contact RYOBI customer service or visit their official webSitio. Conserve su recibo de compra como comprobante de compra.

For further assistance, please refer to the official RYOBI product support channels.