BN-LINK BND-60/U110a-1 Countdown Digital Wall Timer Switch

Introducción

Thank you for choosing the BN-LINK Countdown Digital Wall Timer Switch. This manual provides essential information for the safe installation, operation, and maintenance of your new timer switch. Please read these instructions thoroughly before installation and use, and retain them for future reference.

Información de seguridad

• ADVERTENCIA: Riesgo de descarga eléctrica. Installation requires working with high voltage wiring. Always turn off power at the circuit breaker before installation.
• Este dispositivo requiere un Cable neutro for proper operation. Ensure your electrical box has a neutral wire (typically white) before attempting installation.
• Si no está seguro de alguna parte del proceso de instalación, consulte a un electricista calificado.
• Rated 125V, 60 Hz, 15A/1875W Resistive or General Purpose, 10A/1250W Ballast or Tungsten, ½ HP, TV-5.
• ETL listed, conforms to UL Std. 60730-1, 60730-2-7.

Contenido del paquete

• BN-LINK Countdown Digital Wall Timer Switch
• Placa de pared
• Tuercas de alambre
• Tornillos de montaje
• Manual de instrucciones

Presupuesto

Configuración e instalación

Antes de comenzar: Turn off power at the circuit breaker for the switch location. Verify power is off using a voltage probador.

Instrucciones de cableado

1. Identificar cables: Carefully remove your existing switch and identify the Hot, Load, Neutral, and Ground wires in your wall box. A neutral wire (typically white) is required.
2. Conectar cables: Use the provided wire nuts to connect the BN-LINK timer switch wires to your household wires as follows:
   • Cable negro (temporizador) a Hot Wire (Wall Box)
   • Cable rojo (temporizador) a Load Wire (Wall Box)
   • Cable blanco (temporizador) a Neutral Wire (Wall Box)
   • Cable verde (temporizador) a Ground Wire (Wall Box)
3. Cableado seguro: Ensure all wire connections are secure and insulated with wire nuts.

Montaje y acabado

1. Interruptor de inserción: Carefully push the wired timer switch into the wall box.
2. Interruptor seguro: Use the provided screws to secure the timer switch to the wall box.
3. Fijar la placa de pared: Mount the included wall plate over the switch.
4. Restaurar energía: Vuelva a encender la energía en el disyuntor.

Guía de video de instalación

Instrucciones de funcionamiento

1 Inicialización

When the timer is first powered, all indicator lights will briefly illuminate and then turn off after a self-diagnosis process. This indicates the timer is ready for use.

2. Setting a Countdown Program

To activate a countdown, simply press the button corresponding to your desired time (5, 10, 20, 30, 45, or 60 minutes). The indicator light on the selected button will illuminate, and the countdown will begin. The connected device will turn off automatically once the countdown is complete.

3. Shifting to Another Countdown Program

If a countdown is active and you wish to change the duration, press a different countdown button. The indicator light on the previously active button will turn off, and the light on the newly selected button will illuminate. The new countdown program will then begin.

4. Activating the Daily Repeat Function

To enable the daily repeat function, press the REPETIR button while a countdown program is running. The indicator light on the REPETIR button will illuminate. The current program will automatically run again at the same time on the following day.

5. Deactivating the Daily Repeat Function (2 Ways)

There are two methods to deactivate the daily repeat function:

1. Press REPEAT Button: Presione el REPETIR button again. Its indicator light will turn off. This will deactivate the repeat function for any ongoing program.
2. Press ON/OFF Button: Presione el ENCENDIDO/APAGADO button. This will terminate the ongoing program and also deactivate the daily repeat function.

6. Termination of a Countdown Program

A countdown program will terminate automatically when its set time expires. The indicator light for that program will turn off, and the power output to the connected device will be cut off.

7. Always On Mode

If a countdown is already running, or if the daily repeat function is active, press the ENCENDIDO/APAGADO button twice to set the timer to 'Always On' mode. The ENCENDIDO/APAGADO indicator light will illuminate, and the device will remain powered indefinitely.

If the timer is in 'Off' mode, press the ENCENDIDO/APAGADO button once to set the timer to 'Always On' mode. The ENCENDIDO/APAGADO la luz indicadora se iluminará.

8. Terminating Always On Mode

To terminate 'Always On' mode:

1. Press ON/OFF Button: Presione el ENCENDIDO/APAGADO botón una vez. La ENCENDIDO/APAGADO indicator light will turn off, and the power output will be cut off.
2. Select Countdown Program: Press any of the preset countdown buttons (5, 10, 20, 30, 45, or 60 minutes). This will initiate a new countdown program and terminate 'Always On' mode.

9. Restarting a Running Countdown Program

To restart a running countdown program:

1. Terminate and Re-select: Presione el ENCENDIDO/APAGADO button to terminate the current program, then immediately press the desired countdown button to restart it.
2. Shift Program: Alternatively, press a different countdown button, and then press the original countdown button you wish to restart.

Mantenimiento

To maintain your BN-LINK Countdown Digital Wall Timer Switch, ensure the power is off at the circuit breaker before cleaning. Wipe the surface with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners. Regular inspection for any loose wiring or damage is recommended.

Solución de problemas

• El temporizador no se enciende: Check the circuit breaker to ensure power is supplied. Verify all wiring connections are secure, especially the neutral wire.
• Countdown not starting: Ensure a specific time button is pressed and its indicator light is on.
• Repeat function not working: Confirm the REPEAT indicator light is illuminated after activation. If not, press the REPEAT button again while a countdown is active.
• Device not turning off: Check if the timer is in 'Always On' mode (ON/OFF indicator illuminated). If so, press the ON/OFF button to turn it off.

Garantía y soporte

BN-LINK products are designed for reliability and performance. For any questions regarding installation, operation, or troubleshooting, please contact BN-LINK customer support. We are always here to assist you.

For further information, please refer to the included guide or visit our official websitio.