Producto terminadoview
The BISSELL CrossWave 17132 is a versatile 3-in-1 multi-surface floor cleaner designed to vacuum, wash, and dry hard floors, carpets, and rugs simultaneously. This integrated cleaning system offers an efficient alternative to traditional vacuuming and mopping, providing thorough cleaning with less effort. Its dual tank technology ensures that clean water and formula are always separate from dirty water, guaranteeing a fresh clean every time.
Componentes incluidos
Before beginning assembly, ensure all components are present in the packaging:
- BISSELL CrossWave 17132 Unit (Main Body and Handle)
- Multi-Surface Cleaning Formula (Detergent)
- Multi-Surface Brush Roll (Replacement Brush)
- Storage and Cleaning Tray (Station)
Image: The BISSELL CrossWave 17132 unit shown with its accompanying multi-surface cleaning formula, an extra brush roll, and the storage and cleaning tray.
Instrucciones de instalación
Asamblea
- Inserte el mango en el cuerpo principal de la unidad hasta que encaje firmemente en su lugar.
- Ensure the clean water tank is properly seated on the back of the unit.
- Ensure the dirty water tank is properly seated on the front of the unit.
Llenado del tanque de agua limpia
- Retire el tanque de agua limpia de la parte posterior de la máquina.
- Desatornille la tapa en la parte inferior del tanque.
- Fill the tank with warm tap water up to the 'Water' fill line for the desired cleaning area (small or large).
- Add the BISSELL Multi-Surface Cleaning Formula up to the corresponding 'Formula' fill line.
- Replace the cap and reinsert the tank into the machine, ensuring it is securely latched.
Instrucciones de funcionamiento
Encendido y selección de modo
- Enchufe el cable de alimentación a una toma eléctrica con conexión a tierra.
- Presione el botón de encendido ubicado en el mango para encender la máquina.
- Use the fingertip controls on the handle to select the appropriate cleaning mode: Piso duro or Alfombra.
Proceso de limpieza
To dispense cleaning solution, hold down the spray trigger located on the handle. Release the trigger to stop dispensing.
For best results, make a wet pass by holding the spray trigger and moving the machine slowly forward and backward. Then, make a dry pass by releasing the trigger and moving the machine over the same area to suction up the dirty solution.
Image: A user operating the BISSELL CrossWave 17132 on a hard floor, demonstrating its cleaning action on a liquid spill.
Image: The BISSELL CrossWave 17132 cleaning a tiled floor, effectively picking up scattered dry debris and wet messes.
Mantenimiento y cuidado
Vaciado y limpieza del tanque de agua sucia
- Apague y desenchufe la máquina.
- Retire el tanque de agua sucia de la parte delantera de la máquina.
- Retire con cuidado el filtro y vierta el agua sucia.
- Rinse the tank and filter thoroughly with water. Allow the filter to air dry completely before reinserting.
- Replace the filter and reattach the dirty water tank to the machine, ensuring it is securely latched.
Cleaning the Brush Roll and Brush Roll Window
- Apague y desenchufe la máquina.
- Retire la ventana del rodillo del cepillo tirando de la pestaña hacia arriba.
- Remove the brush roll by grasping the tab and pulling it out.
- Rinse the brush roll and brush roll window under running water. Remove any hair or debris.
- Allow both to air dry completely before reassembling.
- Reinsert the brush roll, ensuring it clicks into place, then reattach the brush roll window.
Imagen: Un primer plano view of the BISSELL CrossWave 17132's brush roll and base, highlighting the multi-surface brush for effective cleaning.
Using the Storage and Cleaning Tray
After each use, place the CrossWave on the storage and cleaning tray. Fill the tray with water up to the indicated line. Run the machine for approximately 10-20 seconds to rinse the brush roll and internal components. This helps prevent odors and maintains performance.
Solución de problemas
Machine Not Dispensing Solution
- Check if the clean water tank is properly filled and seated.
- Ensure the spray trigger is being held down during operation.
- Verify that the formula cap is securely tightened.
mala succión
- Compruebe si el depósito de agua sucia está lleno y necesita vaciarse.
- Asegúrese de que el tanque de agua sucia esté correctamente colocado y sellado.
- Inspect the brush roll and brush roll window for clogs or debris.
- Limpie el filtro y asegúrese de que esté seco antes de reinstalarlo.
La máquina no enciende
- Verify the power cord is securely plugged into a working electrical outlet.
- Verifique si hay disyuntores disparados.
Especificaciones del producto
| Característica | Detalle |
|---|---|
| Marca | Bissell |
| Nombre del modelo | BISSELL Crosswave |
| Número de modelo | 17132 |
| Característica especial | Sweep, wipe and dry (3-in-1 functionality) |
| Tipo de filtro | Con filtro |
| Capacity (Clean/Dirty Water Tanks) | 0.82 litros |
| Quétage | 560 vatios |
| Usos recomendados | Carpeted floors, hardwood floors, upholstery, pet hair removal |
| Factor de forma | Vertical |
| Color | Blue/Titanium |
| Nivel de ruido | 80 decibelios |
| Tipo de controlador | Panel de control integrado |
| Método de control | Tocar |
| Peso del artículo | 5 kg 200 g (11.46 libras) |
| Dimensiones del artículo (LxWxH) | 30 x 23 x 116.8 centímetros |
| Fuente de poder | Eléctrico con cable |
| Volumentage | 220 V |
| ¿Es inalámbrico? | No |
Garantía y soporte
For warranty information, technical support, or to purchase replacement parts and cleaning formulas, please visit the official BISSELL website or contact BISSELL customer service. Always use genuine BISSELL replacement parts and cleaning formulas to ensure optimal performance and to maintain your warranty.
No había vídeos oficiales del producto del vendedor disponibles para incrustar según los datos proporcionados.
