Introducción
This manual provides detailed instructions for the setup, operation, and maintenance of your Anderic RR7083T Remote Control. This remote is designed as a direct replacement for original Hampton Bay UC7083T and other compatible ceiling fan remotes, offering seamless control over your fan's speed and lighting functions.
The Anderic RR7083T is compatible with ceiling fans that have the receiver already installed, specifically models using FAN28R and UC7067FMRX receivers.
Producto terminadoview
Figure 1: Anderic RR7083T Remote Control. This image shows the black remote control with silver buttons for Light, High, Medium, Low, and Off fan speeds. The Anderic logo and model number RR7083T are visible at the bottom.
Características principales:
- Seamless replacement for original Hampton Bay UC7083T remotes.
- Easy dip-switch setup for quick pairing.
- Controls fan speeds (High, Medium, Low, Off) and light (On/Off).
- Diseño ergonómico para un uso cómodo.
- Compatible with FAN28R and UC7067FMRX receivers.
Configuración e instalación
1. Instalación de la batería
The Anderic RR7083T remote requires one CR123A battery (not included). To install the battery:
- Ubique la tapa del compartimiento de la batería en la parte posterior del control remoto.
- Deslice la tapa para abrir el compartimento.
- Insert one CR123A battery, ensuring the correct polarity (+/-) as indicated inside the compartment.
- Vuelva a colocar la tapa del compartimiento de la batería.
2. Dip Switch Matching
For the remote to communicate with your ceiling fan receiver, the dip switches on the remote must match those on your fan's receiver. The receiver is typically located in the canopy of the ceiling fan, near the ceiling.
- Access the dip switches on your existing ceiling fan receiver. Make a note of their ON/OFF (or UP/DOWN) positions. There are typically four switches.
- Open the battery compartment of your Anderic RR7083T remote control.
- Locate the four dip switches inside the remote's battery compartment.
- Adjust the switches on the Anderic remote to exactly match the positions of the switches on your fan's receiver. A switch in the 'ON' or 'UP' position can be represented as '1', and 'OFF' or 'DOWN' as '0'.
- If you cannot access your fan's receiver, you may need to try all 16 possible combinations until the remote pairs with your fan.
- 0000, 0001, 0010, 0011
- 0100, 0101, 0110, 0111
- 1000, 1001, 1010, 1011
- 1100, 1101, 1110, 1111
(Where '1' indicates the switch is ON/UP and '0' indicates OFF/DOWN for switches 1, 2, 3, and 4 respectively.)
- Once the switches are matched, replace the battery compartment cover.
Nota importante:
Ensure the power to the ceiling fan is off before attempting to access the receiver's dip switches. Consult your ceiling fan's manual for specific instructions on accessing its receiver.
Instrucciones de funcionamiento
Once the remote is set up, you can control your ceiling fan and light using the following buttons:
| Botón | Función |
|---|---|
| Light (Bulb Icon) | Turns the fan light ON or OFF. For proper dimming, use incandescent bulbs. Non-compliant bulbs may not dim correctly. |
| HI | Sets the fan speed to High. |
| MEDICINA | Sets the fan speed to Medium. |
| BAJO | Sets the fan speed to Low. |
| APAGADO | Apaga el ventilador. |
Mantenimiento
- Limpieza: Limpie el control remoto con un paño suave y seco. No utilice limpiadores abrasivos ni disolventes.
- Reemplazo de batería: Replace the CR123A battery when the remote's performance degrades or it stops responding. Ensure proper polarity during replacement.
- Almacenamiento: Guarde el control remoto en un lugar fresco y seco, alejado de la luz solar directa y de temperaturas extremas.
Solución de problemas
| Problema | Posible causa | Solución |
|---|---|---|
| El control remoto no responde. | Batería muerta o instalada incorrectamente. | Reemplace la batería CR123A, asegurándose de la polaridad correcta. |
| El control remoto no controla el ventilador/la luz. | Dip switches do not match the receiver. | Verify and match the dip switch settings on the remote to those on the fan's receiver. Refer to "Setup and Installation" section. |
| Light not dimming properly. | Non-incandescent bulbs are used. | Ensure incandescent bulbs are used for dimming functionality. |
| Interferencia o comportamiento errático. | Other devices operating on similar frequencies. | Try changing the dip switch combination on both the remote and the receiver (if possible) to a new, unused setting. |
Presupuesto
- Número de modelo: RR7083T
- Dimensiones: 5.5 x 3 x 1 pulgadas
- Peso: 0.01 onzas
- Tipo de batería: 1 x CR123A (not included)
- Receptores compatibles: FAN28R, UC7067FMRX
- Fabricante: Dan's Electronics Etc., Inc.
- Color: Negro/plata
- Característica especial: Ergonómico
Garantía y soporte
Información de garantía
The Anderic RR7083T Remote Control comes with a 1-YEAR replacement warrantyEsta garantía cubre defectos de materiales y mano de obra en condiciones normales de uso. Conserve su comprobante de compra para reclamaciones de garantía.
Atención al cliente
For technical assistance, troubleshooting, or warranty inquiries, please contact Anderic customer support. Visit the official Anderic websitio o consulte el embalaje de su producto para obtener la información de contacto más actualizada.
También puedes visitar el Anderic Store on Amazon Para más información y productos.
