ICO BATH W1101 Savoy Hardwire Towel Warmer User Manual

1. Introducción

This manual provides detailed instructions for the installation, operation, and maintenance of your ICO BATH W1101 Savoy Hardwire Towel Warmer. Please read this manual thoroughly before installation and use to ensure proper function and safety.

The Savoy towel warmer is designed to add comfort and style to your bathroom by warming and drying towels. It features a contemporary European design and is available in white.

2. Información de seguridad

Instrucciones de seguridad importantes:

• Lea todas las instrucciones antes de utilizar este aparato.
• No sumerja el calentador de toallas en agua ni en otros líquidos.
• Ensure the electrical installation complies with all local and national electrical codes. Installation should be performed by a qualified electrician.
• Este aparato está diseñado únicamente para calentar toallas. No lo utilice para secar ropa ni otros artículos.
• The surface of the towel warmer will become hot during operation. Avoid direct contact with hot surfaces.
• Keep children and pets away from the towel warmer when it is in operation.
• Desconecte la alimentación antes de realizar cualquier mantenimiento o limpieza.

3. Contenido del paquete

Verifique que todos los componentes estén presentes antes de comenzar la instalación:

• ICO BATH W1101 Savoy Hardwire Towel Warmer Unit
• Soportes de montaje y hardware
• Plantilla de instalación (si corresponde)
• Manual de usuario (este documento)

Imagen 1: Frente view of the ICO BATH W1101 Savoy Hardwire Towel Warmer. This image shows the full white unit with its horizontal bars and vertical side rails, designed for wall mounting.

4. Configuración e instalación

The ICO BATH W1101 Savoy Towel Warmer is designed for hardwire installation. Professional installation by a qualified electrician is recommended.

4.1. Lista de verificación previa a la instalación

• Asegúrese de que la energía hacia el área de instalación esté apagada en el disyuntor.
• Confirm the wall surface is suitable for mounting and can support the weight of the unit (approximately 24 pounds).
• Gather necessary tools: drill, level, measuring tape, screwdriver, wire strippers.

4.2. Montaje de la unidad

1. Determine the desired mounting location. The unit dimensions are 25" W x 15.5" D x 3.25" H.
2. Use the provided template (if included) or measure and mark the drilling points for the mounting brackets. Ensure marks are level.
3. Taladre agujeros piloto en las ubicaciones marcadas.
4. Secure the mounting brackets to the wall using the appropriate hardware.
5. Carefully align the towel warmer with the mounted brackets and secure it in place.

Imagen 2: Lateral view of the ICO BATH W1101 Savoy Hardwire Towel Warmer, highlighting its depth and wall-mounted design. This perspective shows the rounded horizontal bars and the sturdy vertical rails.

4.3. Electrical Connection (Hardwire)

Advertencia: All electrical work must be performed by a licensed electrician and comply with all applicable electrical codes.

1. Locate the electrical connection point on the towel warmer (typically at the bottom right, as shown in product images).
2. Connect the towel warmer's wiring to the household electrical supply according to the wiring diagram provided with the unit (not included in this general manual, refer to specific product packaging).
3. Asegúrese de que todas las conexiones estén seguras y aisladas.
4. Install the cover plate over the electrical connection point.

Imagen 3: Primer plano view of the hardwire electrical connection point at the base of the towel warmer. This image details the conduit and the wall plate where the electrical wiring is concealed.

5. Instrucciones de funcionamiento

Once properly installed and wired, operating your Savoy Towel Warmer is straightforward.

1. After installation is complete and verified by a qualified electrician, restore power to the circuit at the breaker.
2. The towel warmer will begin to heat up. The heating process may take some time to reach optimal temperature.
3. Place towels over the bars of the warmer. Do not overload the unit.
4. To turn off the unit, you will typically need to use an external wall switch or timer connected to the hardwired circuit (not included with the warmer).

Imagen 4: Detallada view of the top section of the towel warmer, showing the smooth white finish and the design of the horizontal bars and vertical rail. This image also shows a mounting point.

6. Mantenimiento

Regular cleaning will help maintain the appearance and performance of your towel warmer.

• Limpieza: Desconecte la alimentación antes de limpiar. Utilice un paño suave y seco.amp cloth to wipe down the surfaces. Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish.
• Inspección: Periodically inspect the unit for any signs of damage or loose connections. If any issues are found, disconnect power and contact a qualified technician.

7. Solución de problemas

If you experience issues with your towel warmer, refer to the following common problems and solutions:

8. Especificaciones

Detailed specifications for the ICO BATH W1101 Savoy Hardwire Towel Warmer:

• Modelo: W1101
• Marca: Baño ICO
• Color: Blanco
• Dimensiones (L x An x Al): 25" x 15.5" x 3.25"
• Tipo de instalación: Wall-Mounted, Hardwire
• Forma: Derecho
• Peso del artículo: Aproximadamente 24 libras
• Fabricante: ICO BATH
• Código postal: 644287339516

9. Garantía y soporte

The ICO BATH W1101 Savoy Hardwire Towel Warmer comes with a 2 Years Manufacturer's Warranty.

For warranty claims, technical support, or further assistance, please contact ICO Bath customer service. Refer to the original product packaging or the manufacturer's official webSitio para obtener la información de contacto más actualizada.

Conserve su comprobante de compra para fines de garantía.