1. Introducción y producto terminadoview
This manual provides essential information for the safe assembly, operation, and maintenance of your Yaheetech Horizontal Barbell Bumper Plate Rack Holder. This rack is designed to organize and store Olympic-sized barbell bumper plates and Olympic bars, featuring a mobile design with wheels and a handle for convenient relocation.
Imagen 1: General view of the Yaheetech Horizontal Barbell Bumper Plate Rack Holder.
Características principales:
- Dimensión: 37 x 13 x 11 pulgadas (largo x ancho x alto).
- Max. Capacidad: 300 Lb (136 kg).
- Material: Powder-coated steel frame for resistance to sweat, moisture, and rust.
- Plate Slots: Includes 4 slots, each approximately 5.5 inches wide, to accommodate various bumper plate sizes.
- Movilidad: Equipped with two 2.6-inch diameter rolling wheels and a sweat-resistant handle for easy movement.
- Bar Holders: Two vertical holders for Olympic bars.
2. Información de seguridad
Lea y comprenda todas las instrucciones de seguridad antes de ensamblar o usar el producto. El incumplimiento de estas instrucciones podría causar lesiones o daños al producto.
- Límite de peso: Do not exceed the maximum weight capacity of 300 Lb (136 kg). Overloading can cause structural failure and injury.
- Asamblea: Ensure all bolts, nuts, and components are securely tightened before use. Periodically check for tightness.
- Superficie estable: Always place the rack on a flat, stable, and level surface to prevent tipping.
- Niños y mascotas: Mantenga a los niños y a las mascotas alejados del estante durante el montaje y el uso.
- Mover el rack: When moving the rack, ensure plates and bars are securely seated. Use the handle and wheels for controlled movement. Avoid sudden stops or turns when heavily loaded.
- Inspección: Before each use, inspect the rack for any signs of damage, loose parts, or wear. Do not use if damaged.
- Carga adecuada: Distribute weight evenly across the plate slots to maintain balance and stability.
3. Contenido del paquete
Verifique que todos los componentes estén presentes antes de comenzar el ensamblaje. Si alguna pieza falta o está dañada, contacte con atención al cliente.
- Marco principal (1)
- Plate Dividers (4)
- Vertical Bar Holders (2)
- Conjunto de manija (1)
- Ruedas (2)
- Hardware Pack (Bolts, Washers, Nuts, Wrenches)
4. Instrucciones de montaje
Follow these steps carefully to assemble your barbell bumper plate rack.
- Desempaquetar componentes: Retire con cuidado todas las piezas del embalaje y colóquelas sobre una superficie limpia y plana. Consulte la lista de contenido del paquete.
- Adjuntar ruedas: Secure the two wheels to the designated points on one end of the main frame using the provided bolts and wrenches. Ensure they are firmly attached and can rotate freely.
- Instalar manija: Attach the handle assembly to the opposite end of the main frame. Align the holes and secure with the appropriate bolts, washers, and nuts. Tighten securely.
- Insert Plate Dividers: Slide the four plate dividers into their respective slots on the main frame. These should fit snugly to create the plate storage sections.
- Mount Bar Holders: Attach the two vertical bar holders to the main frame, typically near the wheeled end. Secure them with the provided hardware.
- Comprobación final: Once all components are assembled, double-check all bolts and nuts to ensure they are fully tightened. Gently rock the rack to confirm stability.
Imagen 2: Primer plano view of the rack's handle, designed for comfortable grip during movement.
Image 3: Detail of the vertical Olympic bar holders and one of the rolling wheels.
5. Instrucciones de funcionamiento
This section details how to properly load and move your Yaheetech Barbell Bumper Plate Rack.
- Loading Plates: Carefully place bumper plates into the designated slots. It is recommended to load heavier plates towards the center or bottom of the rack for better stability. Distribute weight as evenly as possible across the four slots.
- Storing Bars: Insert Olympic barbells vertically into the two bar holders. Ensure the bars are fully seated and stable.
- Mover el rack: To move the rack, grasp the handle firmly. Tilt the rack slightly to engage the wheels, lifting the non-wheeled end off the ground. Roll the rack to your desired location. Avoid dragging the rack without using the wheels.
- Colocación: Always position the rack on a flat, stable surface away from high-traffic areas to prevent accidental tipping.
Image 4: The rack fully loaded with bumper plates and barbells, showcasing su capacidad de almacenamiento.
Image 5: A closer look at bumper plates neatly organized within the rack's slots.
6. Mantenimiento
Regular maintenance ensures the longevity and safe operation of your plate rack.
- Limpieza: Limpie el marco de acero con publicidad.amp cloth to remove dust and sweat. Avoid abrasive cleaners that could damage the powder coating.
- Comprobación del hardware: Periodically (e.g., monthly) inspect all bolts, nuts, and connections. Tighten any loose hardware to maintain structural integrity.
- Inspección de ruedas: Check the wheels for any debris or damage that might impede smooth rolling. Clean as necessary.
- Prevención de óxido: The powder-coated steel is resistant to rust, but prolonged exposure to high humidity or moisture should be avoided. If scratches occur, touch up with rust-inhibiting paint.
7. Solución de problemas
This section addresses common issues you might encounter with your plate rack.
| Problema | Posible causa | Solución |
|---|---|---|
| Rack feels unstable or wobbly | Loose hardware; uneven weight distribution; uneven floor surface. | Tighten all bolts and nuts. Redistribute plates evenly. Move rack to a level surface. |
| Las ruedas no giran suavemente | Debris in wheel mechanism; damaged wheel. | Clean wheels and axles. Inspect for damage; replace if necessary. |
| Difficulty moving the rack when loaded | Overloaded; wheels not fully engaged; rough surface. | Reduce weight if exceeding capacity. Ensure rack is tilted to engage wheels. Move on a smoother surface. |
8. Especificaciones
Detailed technical specifications for the Yaheetech Horizontal Barbell Bumper Plate Rack Holder.
Image 6: Dimensional diagram of the plate rack, illustrating key measurements.
| Especificación | Detalle |
|---|---|
| Número de modelo | YT-00073058 |
| Marca | Yaheetech |
| Dimensiones del producto (LxAnxAl) | 37 x 13 x 11 pulgadas (93.98 x 33.02 x 29.97 cm) |
| Peso del artículo | 7.7 kg (aproximadamente 17 libras) |
| Capacidad máxima de peso | 300 libras (136 kg) |
| Material | Powder-coated Steel Frame, Plastic Iron Alloy Steel |
| Number of Plate Racks | 4 |
| Diámetro de la rueda | 2.6 pulgadas |
| Color | Negro |
9. Garantía y soporte
Los productos Yaheetech se fabrican con altos estándares de calidad. Para obtener información específica sobre la garantía, consulte la documentación incluida con su compra o visite el sitio web oficial de Yaheetech. websitio.
If you have any questions, require technical assistance, or need to report missing/damaged parts, please contact Yaheetech customer support through the retailer where the product was purchased or via the contact information provided on the official Yaheetech websitio.
- Soporte en línea: Visita www.yaheetech.shop (or your regional Yaheetech website) for FAQs and contact options.
- Servicio al cliente: Refer to your purchase receipt or product packaging for direct customer service contact details.
