1. Introducción
Thank you for choosing the Maxxima LED Slide Dimmer Switch. This product is designed to provide smooth and reliable dimming for a variety of lighting loads, including incandescent, dimmable LED, and CFL bulbs. It supports both single pole and 3-way circuit configurations, offering flexibility for your lighting control needs. Please read this manual thoroughly before installation and use to ensure proper operation and safety.
2. Información de seguridad
ADVERTENCIA: Para evitar incendios, descargas eléctricas o la muerte, desconecte la alimentación mediante el disyuntor o fusible y compruebe que esté desconectada antes de realizar el cableado. Este dispositivo debe instalarse de acuerdo con todos los códigos eléctricos nacionales y locales.
- Sólo para uso en interiores.
- Do not use with non-dimmable lighting fixtures.
- Not for use with ceiling fans or motor loads.
- Asegurar el agua total.tage of connected bulbs does not exceed the dimmer's maximum rating (600W Incandescent; 200W Dimmable LED/CFL).
- Si no está seguro de alguna parte de estas instrucciones, consulte a un electricista calificado.
3. Contenido del paquete
- Maxxima LED Slide Dimmer Switch (Model: MEW-DM650)
- Placa de pared sin tornillos
- Tornillos de montaje
- Tuercas de alambre
4. Configuración e instalación
This dimmer switch is compatible with both single pole and 3-way wiring configurations. In a 3-way circuit, only one dimmer may be used; the second switch must be an ON/OFF only switch.
4.1 Diagrama de cableado
Refer to the following image for typical wiring connections. Always ensure power is OFF before beginning any wiring.
4.2 pasos de instalación
- Apague la energía: En el disyuntor o la caja de fusibles, desconecte la alimentación de la ubicación del interruptor. Verifique que la alimentación esté apagada usando un vol.tage probador.
- Quitar el interruptor antiguo: Retire con cuidado la placa de pared y el interruptor de la caja de pared. Desconecte los cables del interruptor antiguo.
- Identificar cables: Identify the LINE (hot), LOAD, and GROUND wires. For 3-way installations, also identify the TRAVELER wires.
- Conectar cables: Connect the wires from the wall box to the dimmer switch using the provided wire nuts.
- Black wire on dimmer: Connect to LINE (hot) wire.
- Red wire(s) on dimmer: Connect to LOAD wire (and TRAVELER wire for 3-way).
- Green wire on dimmer: Connect to GROUND wire.
- Regulador de intensidad de montaje: Carefully push the wired dimmer switch into the wall box. Secure it with the provided mounting screws.
- Fijar la placa de pared: Snap the screwless wall plate onto the dimmer switch.
- Restaurar energía: Vuelva a encender la energía en el disyuntor.
4.3 Sensitivity Adjustment (Trim Dial)
The dimmer features a trim dial located underneath the cover plate. This dial allows you to adjust the low-end dimming range to ensure optimal compatibility with various LED and CFL lamps, preventing flicker or premature turn-off at low light levels.
To adjust: Remove the screwless wall plate. Locate the small trim dial at the bottom of the dimmer. Turn the dial clockwise to increase the minimum light level or counter-clockwise to decrease it, until stable dimming is achieved without flicker.
5. Instrucciones de funcionamiento
The Maxxima LED Slide Dimmer Switch features a vertical slide control for dimming and a separate ON/OFF button.
- Encender / apagar: Press the bottom button to turn the lights ON or OFF.
- Atenuación: Move the vertical slide control up to increase light brightness and down to decrease light brightness.
6. Mantenimiento
The Maxxima LED Slide Dimmer Switch requires minimal maintenance. To clean, simply wipe the surface with a soft, damp Paño. No utilice limpiadores abrasivos ni disolventes, ya que pueden dañar el acabado.
7. Solución de problemas
- Lights flicker or do not dim properly: Adjust the sensitivity trim dial (refer to Section 4.3). Ensure your bulbs are dimmable LED or CFL, or incandescent.
- Las luces no se encienden: Check the circuit breaker. Verify all wiring connections are secure. Ensure the dimmer is not connected to a non-dimmable fixture.
- Dimmer does not work with low wattage LED loads: The dimmer may not be compatible with LED loads of 4.5 watts or less. Consider increasing the total wattage of connected LED bulbs.
- Dimmer gets warm: It is normal for dimmers to feel warm during operation. If it becomes excessively hot or emits a burning smell, immediately turn off power at the circuit breaker and consult a qualified electrician.
- Not for use with ceiling fans: This dimmer is designed for lighting loads only and should not be used to control ceiling fans or other motor-driven appliances.
8. Especificaciones
| Característica | Detalle |
|---|---|
| Número de modelo | MEW-DM650 |
| Max Incandescent Load | 600 W |
| Max Dimmable LED/CFL Load | 200 W |
| Vol de funcionamientotage | 120VAC, 60Hz |
| Calificación actual | 5 Amps |
| Tipo de circuito | 3-way / Single Pole |
| Modo de operación | Off, On Off, Slide Dimmer |
| Tipo de contacto | Normalmente abierto |
| Tipo de conector | Tornillos |
| Tipo de actuador | Balancín |
| Material | Cobre (material de contacto) |
| Fabricante | maxxima |
| Listado en ETL | Sí |
9. Garantía y soporte
The Maxxima LED Slide Dimmer Switch comes with a 1 año de garantía from the date of purchase, ensuring safety and reliability. This warranty covers defects in materials and workmanship under normal use.
For technical support, troubleshooting assistance, or warranty claims, please contact Maxxima customer service. Refer to the product packaging or the Maxxima webSitio para obtener la información de contacto más actualizada.
