Introducción
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Poolex PC-NAN heat pump. The Poolex Nano heat pump is specifically designed for small pools and offers efficient heating with a high Coefficient of Performance (COP) similar to larger heat pumps.
Información de seguridad
Please read all safety warnings and instructions carefully before installing and operating this appliance. Failure to follow these instructions may result in electric shock, fire, or serious injury.
- Desconecte siempre la alimentación antes de realizar cualquier mantenimiento o servicio.
- Ensure the electrical system is safe and properly grounded.
- No opere la unidad si alguna pieza está dañada.
- Mantenga a los niños y las mascotas alejados de la unidad durante su funcionamiento.
- Installation must be performed by a qualified professional in accordance with local regulations.
Configuración
The Poolex PC-NAN heat pump is designed for easy installation.
Desembalaje y Colocación
Carefully remove the heat pump from its packaging. Ensure all components are present. Place the unit on a stable, level surface near your pool, allowing adequate air circulation around the unit.
Imagen: Frente view of the Poolex PC-NAN heat pump, showing the fan grille, control panel, and water inlet/outlet connections.
Conexión eléctrica
Connect the heat pump to a conventional electrical socket. The unit comes with a 5-meter power cable equipped with 10mA differential protection for enhanced safety.
Image: Close-up of the 5-meter power cable with integrated differential protection.
Conexiones de agua
Connect the heat pump to your pool's filtration system using the provided PVC connectors (Ø 32-38). Ensure all connections are secure and leak-free.
Image: A set of PVC connectors and clamps used for connecting the heat pump to the pool's water circulation system.
Image: An outdoor scene showing the Poolex PC-NAN heat pump connected to a small, above-ground wooden pool, demonstrating a typical setup.
Instrucciones de funcionamiento
Puesta en marcha inicial
Once all connections are secure and the pool's filtration system is running, plug in the heat pump. The unit will begin to heat the pool water.
Control de temperatura
The heat pump is designed to efficiently raise your pool's temperature. Allow several hours for the water to reach the desired temperature, depending on the pool volume and initial water temperature.
Image: A graphic highlighting the 3000W heating capacity and 600W consumption of the Poolex PC-NAN heat pump, indicating its efficiency.
Economic and Quiet Operation
The Poolex PC-NAN is designed to be economical and quiet during operation, making it suitable for residential use.
Mantenimiento
El mantenimiento regular garantiza un rendimiento óptimo y la longevidad de su bomba de calor.
- Mantenga el área alrededor de la bomba de calor libre de residuos para garantizar un flujo de aire adecuado.
- Limpie periódicamente el exterior de la unidad con un paño suave y húmedo.amp paño.
- Inspect water connections for leaks and tighten if necessary.
- During winterization, follow specific instructions for draining and storing the unit to prevent frost damage.
Solución de problemas
La unidad no se enciende
- Verifique la conexión eléctrica y asegúrese de que el enchufe esté completamente insertado en el tomacorriente.
- Verify that the differential protection on the power cable has not tripped. Reset if necessary.
- Ensure there is power to the electrical outlet.
Calefacción insuficiente
- Check if the pool's filtration system is running, as the heat pump requires water flow to operate.
- Verify that the ambient air temperature is within the operating range for the heat pump.
- Ensure the heat pump is appropriately sized for your pool volume.
Ruidos inusuales
- Compruebe si hay obstrucciones en el ventilador o alrededor de la unidad.
- Ensure the unit is placed on a stable and level surface to minimize vibrations.
Presupuesto
| Característica | Especificación |
|---|---|
| Número de modelo | PC-NAN020 |
| Tamaño | 3000 vatios |
| Tipo de material | Acero |
| Material exterior | Plástico |
| Marca | PILETA |
| Fabricante | estrella de la piscina |
| ASIN | B084MLDVVZ |
| Primero disponible | 19 de febrero de 2020 |
Garantía y soporte
For warranty information and technical support, please refer to the official POOLEX webSitio web o contacte a su distribuidor local. Conserve el recibo de compra como comprobante.
A detailed installation and usage manual is included with your product to provide further guidance.
