Paulmann 94453 Capea LED Lámpara de pared exterior Lamp con manual de instrucciones del detector de movimiento

Introducción

Thank you for choosing the Paulmann 94453 Capea LED Outdoor Wall Lamp. This manual provides essential information for the safe installation, operation, and maintenance of your new outdoor lighting fixture. Please read these instructions carefully before installation and retain them for future reference.

Image: The Paulmann Capea LED Outdoor Wall Lamp, showing the product itself and its retail packaging. The lamp is black, with a conical shade and an integrated motion sensor at the base.

Instrucciones de seguridad importantes

• Seguridad eléctrica: Installation must be performed by a qualified electrician in accordance with local wiring regulations. Always switch off the main power supply before installation, maintenance, or repair.
• Uso en exteriores: This product is designed for outdoor use (IP44 rated). Ensure all connections are properly sealed to prevent water ingress.
• Montaje: Mount the fixture securely on a stable surface. Do not install on flammable surfaces.
• Fuente de luz: The LED light source is integrated and not replaceable by the user. Do not attempt to open or modify the light source compartment.
• Temperatura: No cubra el lamp with insulating material. Ensure adequate air circulation around the fixture.

Contenido del paquete

Verifique que todos los componentes estén presentes antes de comenzar la instalación:

• 1x Paulmann Capea LED Outdoor Wall Lamp (Modelo 94453)
• Instrucciones de montaje
• Herrajes de montaje (tornillos, tacos) - (Assumed, as typical for wall lamps)

Especificaciones técnicas

Image: Technical drawing showing the dimensions of the Paulmann Capea LED Outdoor Wall Lamp: 153mm width, 165mm height, and 96mm depth.

Guía de instalación

Antes de comenzar: Ensure the main power supply to the installation area is switched off at the circuit breaker. Use appropriate tools and safety equipment.

1. Preparar la ubicación de montaje: Choose a suitable wall location for the lamp, ensuring it is a stable surface and allows for proper wiring. Mark the drilling points for the mounting bracket.
2. Perforar agujeros: Perfore agujeros en los puntos marcados e inserte los tacos de pared adecuados (si es necesario).
3. Soporte de montaje: Fije el soporte de montaje a la pared utilizando los tornillos proporcionados.
4. Alambrado: Connect the electrical wires from your mains supply to the terminal block inside the lamp fixture. Ensure correct polarity (Live, Neutral, Earth) and secure all connections tightly. Refer to local electrical codes.
5. Adjuntar Lamp: Coloque con cuidado la lamp fixture to the mounting bracket, ensuring no wires are pinched. Secure the lamp en su lugar.
6. Restaurar energía: Una vez completada la instalación y todas las conexiones estén seguras, restablezca la energía en el disyuntor principal.

Image: The Paulmann Capea LED Outdoor Wall Lamp shown with its packaging, which illustrates basic installation steps and features like the motion sensor and IP44 rating.

Instrucciones de funcionamiento

The Paulmann Capea LED Outdoor Wall Lamp features an integrated motion sensor for automatic operation.

Configuración del sensor de movimiento

The motion sensor can be adjusted to suit your specific needs. Typically, there are controls for:

• Ángulo de detección: Approximately 90 degrees.
• Rango de detección: 2-8 metros.
• Sensibilidad a la luz (LUX): Determines the ambient light level at which the sensor activates the lamp.
  • ON < 20 Lux: El lamp will turn on when motion is detected and the ambient light is below 20 Lux (dark conditions).
  • OFF > 20 Lux: El lamp will remain off when the ambient light is above 20 Lux (daylight conditions).
• Tiempo en: Sets the duration the light remains on after motion is detected. Adjustable from approximately 5 seconds to 5 minutes.

Adjust these settings using the small dials or switches located on the motion sensor unit, usually found at the bottom of the lamp. Use a small screwdriver if necessary.

Image: A diagram illustrating the motion sensor's detection angle (90 degrees), range (2-8 meters), and light sensitivity settings (On < 20 Lux / Off > 20 Lux), along with the adjustable time duration (5 seconds - 5 minutes).

Imagen: Un primer plano view of the integrated motion sensor located at the base of the Paulmann Capea LED Outdoor Wall Lamp, showing its spherical lens.

Mantenimiento

• Limpieza: Desconecte la alimentación antes de limpiar. Limpie el lamp con un suave, damp Paño. No utilice limpiadores abrasivos ni disolventes, ya que pueden dañar el acabado o los componentes eléctricos.
• Fuente de luz: The LED light source is integrated and designed for long-term use (30,000 hours). It is not user-replaceable. If the LED fails, the entire fixture typically needs replacement.
• Inspección: Inspeccione periódicamente el lamp for any signs of damage, loose connections, or wear. Address any issues promptly.

Solución de problemas

Garantía y atención al cliente

Paulmann products are manufactured to high quality standards. This product comes with a 5-year guarantee, as indicated on the packaging. For warranty claims, technical assistance, or further inquiries, please contact your retailer or Paulmann customer support directly. Keep your proof of purchase for warranty purposes.

For more information, visit the official Paulmann websitio: www.paulmann.es

Información de eliminación

This product contains electronic components and an integrated LED light source. Do not dispose of it with general household waste. Please take it to a designated collection point for electrical and electronic equipment recycling in accordance with local regulations. Proper disposal helps prevent potential negative consequences for the environment and human health.