Introducción
This manual provides comprehensive instructions for the installation, operation, and maintenance of the Tridonic Linear Essence Series 43 Watts Constant Current LED Driver. This driver is designed for high-performance constant current output and 0-10V dimming control, making it suitable for energy-efficient commercial lighting systems in the U.S. Please read this manual thoroughly before installation and use to ensure safe and optimal performance.
Información de seguridad
WARNING: Risk of electric shock. Installation should be performed by a qualified electrician in accordance with all applicable national and local electrical codes.
- Desconecte la alimentación antes de la instalación o el mantenimiento.
- Asegure una conexión a tierra adecuada para evitar riesgos eléctricos.
- No exceda el volumen de entrada especificado.tage or output power ratings.
- This device is designed for dry and damp locations only. Do not expose to water or excessive moisture.
- Asegúrese de que haya una ventilación adecuada alrededor del conductor para evitar el sobrecalentamiento.
- The driver is equipped with overload, short-circuit, no-load, and overtemperature protection. However, proper installation is crucial for safe operation.
Contenido del paquete
Verifique que todos los componentes estén presentes antes de comenzar la instalación:
- 1 x Tridonic Linear Essence Series 43W Constant Current LED Driver (Model: TLD-CC43W-UNV-LE2)
Configuración e instalación
Follow these steps for proper installation of your Tridonic LED Driver. Ensure power is disconnected before proceeding.
1. Mounting the Driver
Mount the LED driver securely in a suitable enclosure or fixture. Ensure the mounting surface is stable and can support the weight of the driver. Allow for adequate space around the driver for air circulation to prevent overheating.
Figure 1: Tridonic Linear Essence Series 43W LED Driver. This image shows the overall design of the driver, highlighting its compact form factor and the terminal blocks for electrical connections.
2. Conexiones de cableado
Refer to the wiring diagram on the driver label and the instructions below for correct electrical connections. Use appropriate wire gauges for all connections.
Figura 2: detallada view of the Tridonic LED driver's wiring terminals. This image provides a close-up of the input (AC Line, Neutral, Ground) and output (LED positive/negative, 0-10V dimming control) connections, which are clearly labeled on the driver's casing.
- Potencia de entrada (CA): Connect the AC line (L), neutral (N), and ground (G) wires from your power source to the corresponding terminals on the driver. The driver supports a rated supply voltage de 120-277 V CA.
- LED Output (DC): Connect the LED positive (LED+) and LED negative (LED-) wires from your LED module to the corresponding output terminals on the driver. Ensure correct polarity.
- Control de atenuación de 0-10 V: Connect the 0-10V dimming control wires (0-10V+ and 0-10V-) from your dimming system to the dedicated dimming terminals. This allows for dimming from 10% to 100%.
- Toma de tierra: Ensure the driver casing is properly grounded.
3. Output Current Adjustment (DIP Switches)
The driver features adjustable output current settings (915mA or 1,000mA) via DIP switches. Refer to the driver's label for the specific DIP switch configuration to select your desired output current. Adjust these settings before applying power.
Guía de video de instalación
For a visual guide on wiring and installation, please refer to the official Tridonic Switch Series LED Drivers video below. This video demonstrates the connection process for similar Tridonic drivers, providing helpful visual cues for proper wiring.
Video: Tridonic Switch Series LED Drivers. This video illustrates the wiring process for Tridonic LED drivers, including connecting input power, LED output, and dimming control wires. It provides a practical demonstration of the steps involved in setting up the driver.
Instrucciones de funcionamiento
Once installed and wired correctly, the Tridonic LED driver operates automatically. The primary control is through the 0-10V dimming interface.
- Encendido/apagado: The LED driver will power on when AC input voltagse suministra e.
- Atenuación: Use a compatible 0-10V dimmer connected to the dimming terminals to adjust the light output from 10% to 100%. A 0V signal typically corresponds to the minimum dimming level (10%), and a 10V signal corresponds to 100% light output.
Mantenimiento
The Tridonic LED driver is designed for long-term, maintenance-free operation. However, periodic checks can help ensure continued performance.
- Limpieza: Ensure the driver's exterior is free from dust and debris to maintain proper heat dissipation. Clean with a dry, soft cloth. Do not use liquid cleaners.
- Conexiones: Periodically inspect all wiring connections to ensure they remain secure. Loose connections can lead to intermittent operation or electrical hazards.
- Ambiente: Verify that the operating environment remains within the specified temperature and humidity ranges (Dry and Damp Location, IP20).
Solución de problemas
If you encounter issues with your LED driver, refer to the following common problems and solutions:
| Problema | Posible causa | Solución |
|---|---|---|
| Los LED no se encienden | No input power; Incorrect wiring; Faulty LED module; Driver protection activated. | Check power supply; Verify all wiring connections (L, N, G, LED+, LED-); Test LED module; Cycle power to reset driver protection. |
| LEDs flickering or unstable dimming | Loose connections; Incompatible dimmer; Dimming wires incorrectly connected. | Check all wiring connections; Ensure 0-10V dimmer is compatible; Verify 0-10V+ and 0-10V- connections. |
| El conductor está caliente al tacto | Ventilación insuficiente; Sobrecarga. | Ensure adequate airflow around the driver; Verify total LED load does not exceed 43W. |
| Dimming range not 10-100% | Dimmer incompatibility; Dimmer settings. | Confirm dimmer is fully compatible with 0-10V standard; Check dimmer's minimum/maximum settings. |
Presupuesto
| Característica | Detalle |
|---|---|
| Número de modelo | 87501064 (LC 43/915–1000/50 0-10V fixC lp SNC2 UNV) |
| Tipo | Controlador LED de corriente constante |
| Potencia de salida | 43W (máx.) |
| Vol. nominal de suministrotage | 120-277 V CA |
| Vol. CAtage Rango | 108-305 V CA |
| Frecuencia de red | 50/60 Hz |
| Max. Vol de salidatage (U-OUT) | 60 V CC |
| Interfaz de atenuación | 0-10 V |
| Rango de regulación | 10–100 % |
| Corriente de salida ajustable | 915 mA or 1,000 mA (via DIP switches) |
| Clasificación IP | IP20 |
| Material de la carcasa | Metal, White |
| Funciones de protección | Overload, Short-circuit, No-load, Overtemperature |
| Vida útil nominal | Hasta 50,000 horas |
| Dimensiones del producto (L x An x Al) | 11.00" x 1.10" x 0.90" in. |
| Peso del producto | 7.0 onzas |
| Certificaciones | UL Listed Class P, Meets DesignLights Consortium 4.3 |
Garantía
The Tridonic Linear Essence Series LED Driver is backed by a 5 año de garantía from the date of purchase. This warranty covers defects in materials and workmanship under normal use and service conditions. Please retain your proof of purchase for warranty claims. The warranty does not cover damage resulting from improper installation, misuse, abuse, or unauthorized modifications.
Apoyo
For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact Tridonic customer support or your authorized dealer. Provide your product model number (87501064) and a detailed description of the issue when seeking support.
You can also visit the official Tridonic websitio para recursos adicionales e información de contacto.
