Manual del usuario de la estación meteorológica inalámbrica TFA Dostmann Clear 35.1168.02

1. Introducción

This manual provides detailed instructions for the setup, operation, and maintenance of your TFA Dostmann Clear 35.1168.02 Wireless Weather Station. Please read this manual thoroughly before using the device to ensure correct operation and to prevent damage.

The weather station monitors indoor and outdoor temperature and humidity, and provides a weather forecast based on atmospheric pressure changes.

2. Información de seguridad

• Mantenga el dispositivo y las baterías fuera del alcance de los niños.
• No exponga el dispositivo a temperaturas extremas, vibraciones o golpes.
• Evite la luz solar directa y la humedad.
• No sumerja el dispositivo en agua.
• Use only specified batteries. Ensure correct polarity.
• Replace all batteries simultaneously.
• Dispose of depleted batteries and the device according to local regulations.
• The outdoor sensor should be placed in a sheltered location, protected from direct precipitation.

3. Contenido del paquete

• Base Station (Weather Station)
• Thermo-Hygrometer Outdoor Sensor (Model: 30.3256.02)
• Manual de usuario

Note: 4 x 1.5V AAA batteries (2 for base station, 2 for outdoor sensor) are required and not included.

4. Producto terminadoview

Figure 1: TFA Dostmann Clear 35.1168.02 Wireless Weather Station (Base Unit and Outdoor Sensor).

This image displays the main weather station unit on the right, showing its digital display with atmospheric pressure, weather icons, outdoor temperature and humidity, and indoor temperature and humidity. To the left is the compact outdoor sensor, also displaying temperature and humidity.

4.1 Base Station Display Elements

Figure 2: Close-up of the Weather Station Display.

The display shows: atmospheric pressure (hPa), weather forecast icons (sunny, partly cloudy, cloudy, rainy), outdoor channel indicator (CH 1 OUT), outdoor temperature (°C/°F) and humidity (%), and indoor temperature (°C/°F) and humidity (%).

• Presión atmosférica: Displayed in hPa, with trend arrows.
• Iconos de pronóstico del tiempo: 4 symbols (sunny, partly cloudy, cloudy, rainy) based on pressure changes.
• Temperatura y humedad exterior: From the wireless sensor.
• Temperatura y humedad interior: Measured by the base station.
• Indicador de canal: Shows which outdoor sensor channel is currently displayed (up to 3 sensors supported).

4.2 Base Station Control Buttons (Rear)

Figure 3: Rear of the Base Station showing control buttons and battery compartment.

The rear panel features four control buttons: DOWN, UP, CHANNEL, and SET. These buttons are used for navigating settings, adjusting values, and switching between outdoor sensor channels.

• ABAJO: Decreases values, navigates menus.
• UP: Increases values, navigates menus.
• CANAL: Switches between outdoor sensor channels (if multiple sensors are paired).
• CONJUNTO: Ingresa al modo de configuración, confirma las selecciones.

5. Configuración

5.1 Instalación de la batería

1. Sensor exterior: Open the battery compartment on the back of the outdoor sensor. Insert 2 x 1.5V AAA batteries, observing correct polarity (+/-). Close the compartment.
2. Estación base: Open the battery compartment on the back of the base station. Insert 2 x 1.5V AAA batteries, observing correct polarity (+/-). Close the compartment.
3. The base station will emit a short beep and all LCD segments will light up briefly. It will then display indoor temperature and humidity. The outdoor sensor data will appear shortly after.

5.2 Emparejamiento de sensores

The base station will automatically attempt to connect to the outdoor sensor upon battery insertion. Ensure the sensor is within range (max. 100m in open air). If connection is not established, press the "CHANNEL" button on the base station to initiate a manual search.

The station supports up to three outdoor sensors. To add additional sensors, repeat the battery installation process for each new sensor. Use the "CHANNEL" button to cycle through and display data from different sensors.

5.3 Initial Settings (Atmospheric Pressure)

The atmospheric pressure needs to be set during initial setup for accurate weather forecasting. Consult a local weather service or online source for the current atmospheric pressure in your area.

1. Press and hold the "SET" button until the atmospheric pressure value flashes.
2. Use the "UP" or "DOWN" buttons to adjust the value to your local atmospheric pressure.
3. Press "SET" again to confirm and exit the setting mode.

5.4 Colocación

• Estación base: Place the base station indoors on a flat surface or mount it on a wall. Avoid placing it near heat sources, direct sunlight, or areas with high electromagnetic interference.
• Sensor exterior: Position the outdoor sensor in a sheltered location, protected from direct rain and snow. Ensure good air circulation around the sensor. Avoid direct sunlight to prevent inaccurate temperature readings. The maximum range is 100m (open field).

6. Funcionamiento de la estación meteorológica

6.1 Displaying Temperature and Humidity

The base station continuously displays indoor temperature and humidity, along with the selected outdoor sensor's temperature and humidity.

6.2 Cambio de unidades de temperatura (°C/°F)

To switch between Celsius and Fahrenheit, briefly press the "UP" button outside of setting mode.

6.3 Pronóstico del tiempo

The weather station provides a forecast for the next 12-24 hours using four weather icons: sunny, partly cloudy, cloudy, and rainy. These forecasts are based on changes in atmospheric pressure. The accuracy of the forecast improves after the initial atmospheric pressure setting has been stable for several hours.

6.4 Atmospheric Pressure Trend

Arrows next to the atmospheric pressure display indicate whether the pressure has risen, fallen, or remained stable over the last hour. This helps in understanding short-term weather trends.

7. Mantenimiento

7.1 Limpieza

Limpie el dispositivo con un paño suave y seco.amp Paño. No utilice limpiadores abrasivos ni disolventes. Asegúrese de que no entre humedad en el dispositivo.

7.2 Reemplazo de batería

Replace batteries when the low battery indicator appears on the display. Always replace all batteries in a unit (base station or sensor) simultaneously to ensure optimal performance. Dispose of old batteries responsibly.

8. Solución de problemas

9. Especificaciones

10. Garantía y soporte

TFA Dostmann products are manufactured with quality and precision. For warranty information and technical support, please refer to the official TFA Dostmann webSitio web o contacte a su distribuidor local. Conserve el recibo de compra como comprobante.

Disponibilidad de repuestos: 1 año.

Fabricante: TFA Dostmann

País de origen: China