Stem Aria Linear Light

PRECAUCIÓN

ANTES DE LA INSTALACIÓN

Please read the provided step-by-step instructions thoroughly before proceeding with the installation. You will achieve a secure and successful installation by taking these precautions and diligently following the provided guidelines.

1. Recuerde siempre cortar el suministro eléctrico al circuito antes de comenzar cualquier trabajo de instalación. Las tareas de instalación eléctrica deben ser realizadas exclusivamente por un contratista eléctrico autorizado. Para obtener orientación profesional, comuníquese con su autoridad eléctrica local.
2. Antes de la instalación, verifique el área de instalación para detectar la presencia de otros cables para evitar daños al cableado oculto.
3. When positioning the light fixture, ensure that the chosen area can adequately support the weight of light up to 3kg ( 6.6 lbs, aluminium)/ 7kg (15.4 lbs, brass).
4. Tenga en cuenta que esta luminaria está diseñada para usarse únicamente en ambientes interiores domésticos secos.
5. When handling the metal fixture, make sure your hands are clean. It is advised to wear gloves to prevent leaving marks on the metal surface.
6. Periodically check screws and connections for stability. Gently tighten if necessary, avoid over-tightening.

INSTRUCCIONES DE CUIDADO

Asegúrese de tener las manos limpias antes de tocar la superficie metálica para evitar dejar marcas de huellas dactilares. Se recomienda utilizar guantes al manipular la luminaria. No utilice sustancias abrasivas en el producto. Tenga cuidado con su peso. Tratar con cuidado.

Over time, the metal surface may diminish its original luster. To retain the original aluminium or brass finish, use metal polish with a soft, dry cloth and gently rub it onto the surface.

DETALLES TÉCNICOS

• Dimensiones
  • Dia.. 26 L1440 MM
  • Dia 1 L56.7 IN (Custom length on request)
• Material y peso
  • Cast Aluminium – 2.5 kg
  • Cast Brass – 6 kg
• Clasificación Kelvin 3000K
• Fuente de luz
  IND/ UK/ EU LED strip (Incl.)12W, 220-240V
• Classification IP20
• Dimmable Phase cut, TRIAC compatible
• Hardware
  W56 H32 D140 MM W2.2 H1.3 D5.5 IN Aluminium, Brass finish
• Cable
  • Cableado
  • Cord length – 2000 MM

DENTRO DE LA CAJA

* Driver and LED light are not included for regions with a voltage requirement of 110-120V.

(Figura 1)

PASO 1

Position and drill

Carefully mark the position where you intend for the light fixture to hang. Use the dimensions marked (Fig. 1) as a guide to drill holes in the ceiling, then proceed to the next step.

(Figura 2)

PASO 2

Install the Clutch wire gripper and Canopy back plate

1. Connect the clutch wire gripper (A1) and canopy back plate (B) by fastening them at the drilled holes in the ceiling using the drywall screws (Fig. 3).
2. Insert the clutch wire (C) through the clutch wire screw (D)(Fig. 4), fitted on the ends of the cast Rod.
3. Secure the opposite end of the clutch wire gripper (A1)(Fig. 3).
   1. To ensure the safe suspension of the light fixture, check that the wires are firmly attached to the clutch wire grippers and are devoid of any slack.

(Figura 5)

PASO 3

Install the second Clutch wire gripper

Take the second clutch wire gripper (A2) and fasten it directly onto the ceiling (Fig. 6) using the drywall screw. Now insert the clutch wire (C) through the clutch wire screw (D) (Fig. 4) and securely attach it to the clutch wire gripper (A2) (Fig. 6).

(Figura 7)

PASO 4

Install and level the Rod

Fasten the clutch wire screw (D) to both ends of the Rod (Fig. 7) and adjust its height as desired. Ensure that the light fixture is in alignment with the floor.

(Figura 8)

PASO 5

Connect the wiring to the driver

1. Insert the LED cord end (F) on the Rod through the hole in the canopy casing (E) and connect it to the driver output mounted on the ceiling (Fig. 8).
2. Connect the driver input to the electrical connection in the ceiling (Fig. 9).
   Ensure that all connections are secure and that there are no exposed wires or electrical hazards. Pay attention to the polarity of the connection. A wrong connection can cause damage.

(Figura 10)

PASO 6

Close the Canopy casing

After completing the installation, take the canopy’s top cover and attach it to the back plate (Fig. 10) using the canopy screws (Fig. 11). Ensure that the wiring and any excess clutch wire strands are neatly trimmed after the installation.

In case you require further assistance, please write to us at info@stemdesign.co.

Preguntas frecuentes

¿Puede utilizarse el aparato en exteriores?

No, the fixture is designed for use in dry domestic indoor environments only.

¿Qué incluye la caja?

The box includes light source, hardware, cord, wall plugs, drywall screws, clutch wire gripper, clutch wire, gloves, canopy casing with driver, rod with LED light, and clutch wire screws.

Is the driver and LED light included for all regions?

Driver and LED light are not included for regions with voltage requirement of 110-120V.

Documentos / Recursos

stem Aria Linear Light [pdf] Manual de instrucciones Aria Linear Light, Linear Light, Light

Referencias

• Manual de usuario