Synapse CSEN1 Combo Sensor Controller Installation Guide

INSTALACIÓN
CSEN1

CSEN1 Combo Sensor Controller

Part Numbers: CSEN1-H-W-ZHA (white enclosure) and CSEN1-H-G-ZHA (gray enclosure)

DESCRIPCIÓN

The CSEN1 is a low voltage Networked Lighting Controller with an integrated passive infrared sensor and a photocell. It is powered via the AUX power from the LED driver. The CSEN1 autodetects both 0-10V Drivers and D4i Drivers to simplify the installation. The product is DLC certified for both indoor and outdoor applications.

PRESUPUESTO

• Radiofrecuencia: 2.4 GHz (IEEE 802.15.4)
• Potencia de salida de transmisión RF: +20dBM
• Temperatura de funcionamiento: -40° a +70° C
• Humedad de funcionamiento: 10 a 95 %, sin condensación
• Carcasa con clasificación IP66
• Dimensiones: 3.1” Pr. x 1.6” Al. (80 mm Pr. x 42 mm Al.)
• Input Power: 12-24VDC, 35mA max, 840mW
• Finalidad del control: funcionamiento
• Environmental: Indoor/Outdoor
• Grado de contaminación: 3
• Impulso nominal Voltage: 330 V

CONSIDERACIONES DE DISEÑO

Below are some recommendations for successful analog dimming using the CSEN1. The analog dimming control wires are referenced as DALI+/DIM+ and Common Ground/DALI-. The dimming signals have a Maximum voltage de 10V DC.

• Do not ground the Common Ground/DALI- wire to chassis ground; this is a return signal and is critical for proper dimming.
• Dirija los cables de atenuación lejos de las líneas de CA si es posible.
• Máximo de 4 controladores LED DALI-2/D4i por controlador; consulte con el soporte de Synapse si necesita una proporción mayor.
• Maximum of 8 DIM to OFF LED Drivers for DIM to OFF Designs.
• No lo monte en un disipador de calor ni en un controlador LED.

NOTA: El controlador LED debe admitir la funcionalidad DIM to OFF.
ADVERTENCIAS Y PRECAUCIONES

• TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
• The CSEN1 should only be installed in a fixture with a Zhaga Book 18 receptacle.
• El incumplimiento de estas instrucciones y advertencias podría anular la garantía.
• This product must be installed in accordance with national, state, and local electrical codes and requirements.
• If you are unsure about any part of these instructions, consult an electrician; qualified personnel should perform all work.

DETALLES DE CABLEADO DEL TOMA ZHAGA BOOK 18

TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
For fixtures with an existing Zhaga socket, prior to installation, verify the wiring per the details below. (See Figure 1) If the fixture does not have a Zhaga socket, use the appropriate Wired Adapter accessory based on the knockout size: CSEN1-ZHA-ADPT-22 for 22mm knockouts, or CSEN1-ZHA-ADPT-33 for 33mm knockouts. The specifications for the signal wires are:

• 12-24VDC POWER: Brown
• Common Ground/DALI-: Pink with White Stripe
• DALI+/DIM+: Violet with White Stripe
• Solid Conductor, 105°C, Rated for 600VAC, AWG 20, 15” Length

FIGURA 1

INSTRUCCIONES DE INSTALACIÓN

TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!

1. Si corresponde, retire la tapa de sellado o el dispositivo de control de iluminación actualmente instalado en el receptáculo de la lámpara.
2. Align the CSEN1 such that the contacts pins are positioned at the appropriate the receptacle contacts.
3. After alignment, push until the CSEN1 is fully seated within the receptacle.
4. While pushing against the device, twist the CSEN1 housing clockwise until it locks into place. The CSEN1 includes a latching key or notch that will lock into position with an audible “click”. (See Figure 2)

Nota: Para funcionar correctamente, asegúrese de que el controlador esté completamente insertado en el enchufe y girado hasta la posición de bloqueo.
Advertencia: The Zhaga receptacle should not turn during installation. Turning the receptacle could damage the internal fixture wiring by pulling it loose.
FIGURA 2

LED DE ESTADO

INFORMACIÓN REGLAMENTARIA Y CERTIFICACIONES
RF Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Certificaciones de Industry Canada (IC): este aparato digital no supera los límites de Clase B para las emisiones de ruido de radio de los aparatos digitales establecidos en las Regulaciones de interferencia de radio del Departamento de Comunicaciones de Canadá.
Certificaciones e información reglamentaria de la FCC (solo EE. UU.)
FCC Parte 15 Clase B: Este dispositivo cumple con la parte 15 de las reglas de la FCC. El funcionamiento está sujeto a las dos condiciones siguientes: (1) Estos dispositivos no pueden causar interferencias dañinas y (2) Estos dispositivos deben aceptar cualquier interferencia recibida, incluidas las interferencias que puedan causar un funcionamiento perjudicial.
RADIO FREQUENCY INTERFERENCE (RFI) (FCC 15.105): This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Re-orient or relocate the receiving antenna; (2) Increase the separation between the equipment and the receiver; (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; (4) Consult the dealer or an experienced radio/TV technician for help.
Declaration of Conformity (FCC 96-208 & 95-19): Synapse Wireless, Inc. declares that the product name CSEN1 to which this declaration relates, meet the requirements specified by the Federal Communications Commission as detailed in the following specifications:

• Parte 15, Subparte B, para equipos Clase B
• FCC 96-208 según se aplica a las computadoras personales y periféricos Clase B
• Este producto ha sido probado en un laboratorio de pruebas externo certificado según las normas de la FCC y se ha determinado que cumple con los límites de emisión de la Parte 15 de la FCC. La documentación está en file y disponible en Synapse Wireless, Inc.

Si la identificación de FCC para el módulo dentro de la carcasa de este producto no está visible cuando se instala dentro de otro dispositivo, entonces el exterior del dispositivo en el que se instala este producto también debe mostrar una etiqueta que haga referencia a la identificación de FCC del módulo adjunto. Modificaciones (FCC 15.21):
Los cambios o modificaciones a este equipo no aprobados expresamente por Synapse Wireless, Inc. pueden anular la autoridad del usuario para operar este equipo.
Patentado – marcado virtual en https://www.synapsewireless.com/about/patents
Para obtener más información, visite: synapsewireless.com

CERTIFICACIONES

Controlador de aplicaciones certificado DALI-2